Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
According to the datasheet:
Does this mean that when i change my vdd from 3V to 2V, then the current peaks will be reduced? If so what does this:
graph means...
Hello,
I'm currently designing a custom bootloader to perform a DFU. So far I'm able to update the bootloader and the application, however there is a problem when I try...
I have been studying MQTT these days.
I'm testing the program below. https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160/mqtt_simple/src/main...
I use nrf52832 sdk15.2 to develop products, use WDT to prevent program crashes, WDT set time is 10S, nrf52832 will be paired and bound after connecting with IOS phone, when...
Hi!
I am trying to use the SAADC driver on SDK13, following some examples from the playground repo. I am using the app timer to trigger a measurement for 4 channels. ...
Hello,
I cant seem to find a PBKDF2 function in the SDK to generate a private key from a passphrase.
We want to use mbed-tls or CC310 to make a SHA512 based key for AES...
Hi Everyone,
I have a custom board with nRF52840 and am testing out basic GPIO functionalities with some LEDs. In the board, the LED cathode is connected to nRF52840 GPIO...
Using nRF Connect for PC Version 2.6.1
Connect to a peripheral device that ask for an ATT_MTU > 247 bytes
NRF Connect fails with
Failed to call gattsExchangeMtuReply...
Hi
I have implemented (heavily base on the found examples) an application which uses both ESB and BLE. For now I focus on developing the ESB part of the SW. I am using the...
Hi Sir,
According to the nRF52832_PS_v1.4.pdf, In section 17.1.1, the table shows the current consumption of Radio. What's difference w/ Iradio_tx0 and Is0? Why do we get...
Dear Nordic Team,
We are building a very low power wearable with the nRF52810, only powered by a small solar cell and a super-capacitor.
We would like to offer firmware...
Hey,
I am working on nRF52 DK boards. Suddenly PC is not detecting the one of my DK board, but the nrf53832 processor's LEDs are functioning as per the last program dumped...
I am trying to use multiple channels for beacon transmission.I want to hop to a different channel at an interval of 2 seconds.I have configured one device as a pan coordinator...
Hello,
I'm using following code to read two channels of SAADC. It works fine when device is not connected to BLE central device. As soon as it's connected, the saadc_callback...
Hello,
I want to use 2 thingy:52 board in which one will act as master and other as slave. If yes, how can we do it? please provide any example code. Thank you.
