Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
I am using SDK 15.2.0 in nrf52840, pca10056 and s140. I want to combine two codes of SAADC and ble_app_uart. I have added every driver files and path for these files...
Hi, I started a 4 layers PCB design in cad-soft Eagle. In nrf52840 ref design they are using blind vias in 1 to 2 layer, so I'm guessing below DRC layer setup is correct for...
Dear Nordic,
I want to test BLE Mesh network. for that one board(nrf52832 DK board is programmed with client example. when i debug the program its entered into app_weak_errors...
Hi
I am using nrf51822 , sdk version 11 and softdevice version 130
In project I am trying to disable SPI1 and TWI0 channel by using following command
NRF_TWI0->ENABLE...
Hi, I are using BT832 module based on NRF52832-QFAA IC in an application. Please provide the following details regarding ble transmission of NRF52832-QFAA-R7 IC
1) modulation...
Hello,
I´ve got a corrdinator, which establishes my network. Also I´ve got an End-Device that joins the network successfully.
Is there any chance for me to observe the...
Hi Nordic,
I am working on a project where I connect via nrf52 DK, to a peripheral. I am runinng on SDK15, with the experimental build ble_app_interactive, inside the ble_central_and_peripheral...
I'm using nRF52832 with SDK 15.0 and Softdevice S132. Within ble_dfu.c anytime a connection is established the on_connect function blindly sets m_dfu.conn_handle = p_ble_evt...
hello nordic ,
i want to download the mesh SDK 2.1.1 to use the light switch example to transform the model simple onoff from sending uint8_t to string ,
i have started...
Hello, I'm using softdevice 6.0 and SDK 15.
In my application, I would like stop the SAADC at the disconnection and then restart SAADC at the connection to power saving...
hi..........
i am using nrf42840 ...segger 15.2 version
i am facing the problem in sleep mode
i used the command to sleep
static void power_manage( void ) { ret_code_t...
Hi guys,
I am currently using nrf51822 with SDK 11. I use Peer Manage to deal with paring and bonding encryption in BLE connection.
Please correct me if I am wrong but...
Hi,
When I'm trying the throughput on nRF52840 with SDK v14.2, I set up a 52840PDK as a 'repeater'; in which case the 'repeater' will receive the output (20kBytes in total...
which app should I use when I want to do LL BQB test with harmony on nRF52840?
it can not connected with harmony when I use DTM project. It seems the interface of nRF52840...