What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
using nRF52832, SDK 15.1, custom made units.
My Obervations - (in bootloader settings) $nrfutil settings display ota46to47.hex
when device is flashed "Current bank"...
Hello,
For BLE mesh light_switch example, the following statement is showing error.
In app_config.h
#define NRF_SDH_ENABLED 0
In sdk_config.h
#ifndef NRF_SDH_ENABLED...
Can someone tell me how to make device go to sleep and make it wakeup after a few hous using systick timer. I know how to create a timer but i wanna know which system call...
Hello. I have a breakout board (SMARTMP3 VS1053) and it has also a slot for memory card, so I connect the wires (SCK, MOSI, MISO and CS) to my nrf52832, but it can't see the...
What is the recommended way to protect characteristic value from modification while it is being read by a client?
I have a test application with 500-byte long characteristic...
Dear Team,
is there a tutorial on how to start from scratch a project for zephyr nrf91? With all configurations and flags...
That would be great!
Thanks & cheer
O...
Hello,
We're trying to create a custom bootloader from scratch and we're struggling with a weird behavior. This is for the nRF52840 and the bootloader doesn't use the softdevice...
The SDK version is 15.0.0, SD 132, single peripheral conection.
the configuration:
this is how i request the timeouts:
With the timeouts of about 50ms and less, the...
Hi guys,
I tried to modify "configs.c" or ".config", modified CONFIG_GPS_SIM_TRIGGER_TIMER_MSEC = from 2000 to 10000 .
But the device still sends GPS data every 2 seconds...
Hi there
I have a design in production using Gazell at 250kbs on a NRF51822
I would like to update the design using a nRF52840 but it doesn't support the data rate that...
Hi,
We are looking for a consultant to help us port our product's ( https://www.ncase.io ) firmware from Simblee to the Nordic nRF51822 or nRF52832. Experience with Nordic...
Dears:
I test the uart dfu by examples\dfu\secure_bootloader\pca10056_uart
After I enter command like below：
nrfutil dfu serial -pkg Sena_app_uart_s140.zip -p COM5 ...
My project is Obj-C , and “ pod 'iOSDFULibrary' ” in my Podfile.
It worked fine until I upgraded Xcode to 10.2. There are some errors(about 100) occurred during project...
Hi all
I am doing multiprotocal from sdk15.3 and I am trying to add nrf_gzp.c, nrf_gzp_host.c, and nrf_gzp_host_nrf5x.c in to the project
after compile successfully and...
I was wondering, is it possible to suspend/resume flash operation in nRF52840 (internal flash)? Like flash erase suspend, and also flash write suspend/resume?
Thank you...
