Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi,
I am trying to use the Power Profiler Kit (PPK) to asses the power consumption on a nRF52840 - PDK. I have not managed to get anything wokring.
The exact hardware...
I am using 3 nRF 52840 dongles and want to establish mesh network between them. So I flashed the dongle with the softdevice (s140_nrf52_6.0.0_softdevice), bootloader (mesh_bootloader_serial_gccarmemb_nrf52840_xxAA...
I have flashed the the mesh serial hex file to nRF52840 dongle through nRF connect programmer application. I am getting following error
1. Reopen device failed
2. Nordic...
Hello All, In one of our product we are using nrf52840 Bluetooth + MCU IC. Size of Product is very tiny. which types of Antenna is better for range of 25 meter to 30 meter...
Hello good morning,
I am using nrf52840 device. I am sending 20 bytes using notification at different notification intervals like 30ms, 80ms and 1sec. But at application...
Hi, I wrote the firmware in SDK 11 preview, and when migrating it to SDK 11 the NFC code does not work, also it seems when the NFC startup code is executed none of the GPIO...
Hi All,
I've not enough experience in nrf51822. I'm developing a battery powered device using the Nordic nrf51822 pca10028. I want to connect two nrf51822 pca10028 boards...
I would like to use the latest ARM Compiler Version 6 ( armclang ) because I need some features of the C++11 language.
Is it possible to use the latest ARM Compiler Version...
Hi all,
I am using keil uVision 5 and nRFgo studio version 1.21.
I am trying to flash softdevice and application in nRF52832, but my device(nrf52-DK) is not getting connected...
I'm having some trouble getting interrupt from RTC1. I'm initialising as follows.
I have an interrupt function as follows.
I'm using the gcc_startup-script. We're...
I have Zephyr stack for BLE hci_uart without any error it got compiled in nordic controller part, but i like to use zephyr stack in host without linux OS. Is it possible to...
Hi,
If I do a directed advertising (peripheral device) with specific peer address, then will the peripheral device visible to other phones ( whose peer address does not...
I have tried out the Running Speed and Cadence Application of SDK 15.1 with the new DK "PCA 10056" (1.0.0, 2018.19, 683681562). We used the Samsung S8 and S9 with Android...
Hello
Just a fairly simple question.
Do you have a documented step-by-step instructions on how to control and toggle the on-board LED on the nRF52 DK
using the Nordic...
