Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi.......
i am student , i am doing a project based on temperature. i want transfer data from temperature sensor to phone via using NRF connect . can you help me ? how to...
How send the larger data,which is more then 300 bytes in spi master example.i am using the Sdk 15.0.how to enable the spi .please send the default pins used for the spi.
Above is the "inverted—F" PCB antenna referenced.Below is the RF SCH and PCB layout,the PCB diameter is 20mm.Chip we use nrf51822 and bal-02d3.
Can the antenna work...
Playing with the logging and cli commands for logging, I normally get this if all my modules are lowercase named (but also if they are alfabetically after CLOCK):
It seems...
I have met a problem, that I can't download the previous version of nRF5 SDK, like 15.0.0, but only the lastest,15.2.0. Because a lot of work of mine is based on version 15...
I have successfully built and run the mesh examples 2.2.0, on several nrf52832dk boards with the exception of the EnOcean Switch example.
I can successfully build and launch...
Hello,
I like to create a BLE Device with a nrf51822 which is able to receive 2 states from a BLE Phone. My idea is to set up a BLE Service within this BLE Device which...
Hi I'm attempting to transfer some text strings over ble I have a nRF51 as master and a AVR & HM-10 module as peripheral. The peripheral/AVR side I have working fine - When...
Hi,
I am currently working with nrf52832 chip.i tried light-switch demo examples in mesh SDK v2.2.0.working fine.Now, my requirement is mentioned below
A--->B----->C...
Hi
I'm using nrf51822 & PCB antenna due to size constraint I changed antenna direction (edit library file) so that it will fit within size. Also, components placement slightly...
Hi, our current Android application is based on nrf uart app example and we want to restart an implementation based on template example on top of BleManager library. Could...
Hi Nordic, I am working on NRF52 DK, with the example program ble_app_interactive, SoftDevice S132. I am trying to connect to peripheral board, but I can't establish an connection...
Hi All,
I am currently working in a team desigining a wearable that uses BLE in 2.4 GHz band to communicate with smartphones and other devices. We have been working with...
Hello developer's!
I am able to build Flash_fstorage_example in segger embedded studio, But when i press continue execution button, it take's me to
app_error_weak.c file...
I am trying to integrate a pressure sensor with our system and Nordic has libraries for LPS22HB sensor. I ordered STEVAL-MET001V1 from ST and try to modify the TWI-sensor...
