Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I've been searched windows sample application for bluetooth.
I got android sample code but I need MFC sample code now.
If you have the sample code please let me know.
...
I've been playing around with the multi-central central/peripheral examples and I thought I would modify the peripheral to instead use a service I had written for another...
Hello,
If I supply 1.85V on the "External supply" pins, can i use all the modules of the board (nRF51DK)?
I need to have less than 2V on some of the pins as an output...
Our application is a smartband based on nRF 51822 with SDK 9.0 S130, and we found that the device will stop advertising unexpectedly (application is still alive). We have...
Looking at the radio section of the nrf52832 data sheet I see that in section 21.1.2 Packet configuration it is stated that
"For all modes that can be specified in the MODE...
Hi everyone,
Just a brief introduction about my system, I am currently working on Brain computer Interface which was funded by NSF. In our system we have Sense electronics...
hello there , i have put my nrf51 dk in system off mode.then i am generating interrupt using button 3 to wake up it. but my nrf51dk can't wake up. can you hel p me??
my...
Hello.
I use nRF52 DK, S132v2 and PCA10040.
I want to get timestamp like GetTickCount of C++.
When I searched Documentation, I found RTC what can do like GetTickCount...
Hi,
When I finish coding, I can generate .HEX file for all products. But for real mass production, I may need to flash a seperate serial number in somewhere for each PCBA...
I'm trying to transfer a txt file by sending it from a terminal to my NRF52 DK with the BLE_UART example. I always get a BLE_ERROR_NO_TX_PACKETS avter a few packets though...
Hello, everybody. We have a custom board with nRF51288. We also have code based on ble_template that is working on Nordic devboard and dongle. Code is also working on our...
I am having difficulties porting the SPI Master demo to an S130 Soft Device on SDK 11.0.0. From the looks of it, there seem to be some issues with interrupts but I am unsure...
Using S130,
Central device,
Manual whitelist,
custom hardware.
Manual connection to 1 or 2 peripherals depending on a switch position.
This device is a central that...
hello there . i want to do something like when i press button advertisement starts. when i release button advertisement stops. can anyone tell me how to do this?? any sample...
Looking at Table 40 in the nRF51 Series Reference Manual v3.0, the Memory Protection Unit prevents request sources in Code R1 from writing to RAM R0. But if the request source...
