Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I've been reading about minimizing the amount of time that the SoftDevice blocks the CPU for, but most of the answers have to do with old revs of the chip and old versions...
We have a peripheral device that we would like to have sleeping 99% of the time. I have a single timer waking it at 1-second intervals to look for things it might need to...
Hi,
I am trying to get date and time on my nrf51822 but struggling a bit. I would like the nrf to receive the time over BLE and then increment it internally using the RTC...
I have a system using the Gazell link layer in which 2 devices stream data to a single host. Each of the devices is assigned a different pipe, and all three (host, and both...
I have successfully set up UART/Serial Port Emulation over BLE example. I have modified it so that it works with two nRF51 DKs, one acting as a central and other acting as...
Hello,
I would like to know whether the below PA can be interfaced with nRF51822?
For our application we need to increase the power of the BT. so I have selected the below...
Hi,
From other forum posts it seems to be very important to follow the reference layouts when designing nrf52 PCBs, but I can only find the reference files in Altium format...
Hi,
I have a nrf51 dongle and I try to connect my Android smartphone to it. My smartphone is BLE compatible, so no problems here.
I flash the firmware using master control...
I am a newer for Nordic's BLE.
and has WaveTek nRF51822 BLE Shield (design for Nordic), and downloaded the S110 softdevice version 7.3.0 and the wavetek_connectivity _s110v1...
Hi
I have some problem about the HomeKit SDK,is there anyone could help me?
In the HomeKit SDK,such as lightbulb project,there is a function mfi_i2c_configure that...
Hi Nordic guys,
we are developing a peripheral device with a custom protocol to exchange data.
we are using nrf51822 with SDK 6.0 and SoftDevice 7.1.0 (s110 being peripheral...
I can not find information about layer stack-up and whether the via-in-pads were filled, please provide this information. We are thinking about a variant with thin outer layers...
Hi, I am trying to combine SPI, microESB and BLE. BLE and microESB will not be combined in realtime, but rather be two distinct modes, and not run at the same time, and therefore...
[test result] change to use Timer1 of timer example,it failed. if you use timer0, it is OK..
SDK IS 9.0:
nRF51_SDK_9.0.0_2e23562\examples\peripheral\timer
[test step...
