Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I am working on a custom nRF552832 board. I need to use the reset pin (p0.21) as GPIO input.
I am using the NRFConnect plugin on VSCode to develop and program the board...
Hello,
We are using the nRF52840_CKAA_R7 package of the nRF52840 on our custom board. The USB pin connections are designed based on the nRF9160-DK's nRF52840 reference....
I would like to be able to open a bash prompt with the nRF Connect SDK (NCS) v2.0.0 toolchain environment loaded without going through Toolchain Manager ("open bash" option...
We are evaluating the nRF5340 chip for a Bluetooth LE audio broadcast streaming application.
Is it possible to use adaptive frequency hopping with the BLE audio network...
For the RADIO peripheral of the nrf52(840), if you set up the radio to receive coded Phy transmissions, I have the opportunity where I can set the MODE for 125Kbps or 500Kbps...
I'm trying to use nordic's BLE sniffer on a nRF52833-DK. I have programmed it with the firmware "sniffer_nrf52833dk_nrf52833_4.1.1.hex".
I've then tried both the command...
When I use nRF Programmer on my laptop (v3.0.7) to update firmware on my Thingy53 with a USB cable and SW2, the programming seems to finish normally, but it prints "Bluetooth...
Hi, I'm having Bluetooth LE peripheral nus code which works fine with v2.7.0 with nrf52840DK (I can connect with an Android App and stream data etc): Changing the build configuration...
NCS 2.7
NRF52840
Building with sysbuild, MCUBOOT, and 2 different applications (mfg and end-user)
My custom board includes a sensor fusion IMU from bosch. The firmware...
Hello,
I want to test nRF21540 EK with a nRF5340 DK.
I am using ncs 2.7 , and don't want to use sys build . I want to use child image/ hci_ipc .
I modified ncs/zephyr...
We have devices that have low signal so they have to reconnect to AWS a lot. We have a watchdog timer with a 100s timeout that we feed every 10 seconds in the control loop...
Hello everyone!
I am having trouble with my current setup and I would like to ask you for your advice.
I am developing a central station featuring nRF5340+nRF7002. This...
I generated an overlay file with the following info:
and there is my main.c file:
However, when I tried to debug my code to understand what was wrong, I got the...
Hi,
I am using nrf52840 and implemented shell interface. I have testing it over uart and uart over usb. At any given moment it can be enabled over 1 interface in device...
