Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Using the "launcher" the open button appears to do nothing and the update from V4.2.0 to V4.2.1 produces an error message.
Twice I have uninstalled V5.1.0 and replaced it...
I'm using an nfr52840 board.
I noticed that when using The 'zephry-sdk' v3.5.99-ncs1-1, when doing a passive scan using:
BT_LE_SCAN_ PASSIVE
which sets:
BT_LE_SCAN_PARAM...
Hi Everyone,
I am trying to develop a simple application with the XIAO BLE Sense device, the idea is to send a BLE message with a something hits the device. To achieve this...
To output PWM signal as early as possible after powering on the NRF5340DK, I added the same code in mcuboot/boot/zephy/main.c and mcuboot.overlay as in the app core. This...
I reference the sample at https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-6-analog-to-digital-converter-adc/topic/exercise-3-interfacing...
I have a packet that I am sending out using the nrf52840. Using another piece of code supplied by Emil Lenngren, information from the solar_sensor_beacon project and raw data...
Hi,
I am using the NRF52840 dongles for BLE communication with S140 and the NRF5 17.1.0 SDK. I have plugged each dongle in a Raspberry Pi 3B+, and have set the DCDC regulator...
Hi, We are developing a product which is reading RTDs and thermistors from the NRF52833's internal ADC. We're working on compensating for the intrinsic errors of the ADC and...
Hello,
In my device I have a nrf52840 which communicates with a STM32 via uart.
In my nrf52840 I use the MCUboot.
Is there any documentation or source code that would...
Hi all,
I am developing my own provisioner with the nrf52840 chip. My idea is to be able to add at least 2000 nodes to a bluetooth mesh network with the provisioner but...
Hi, I'm delevoping an appilcation which can generate one sample per 20 us (accomplished with timer0) and transmit one ESB packet when 20 samples are collected. Below is the...
I'm using NCS 2.7.0 and NCS 2.9.0 to read the BT stack version information on an nRF5340. See below for the results.
How should the fw_version, fw_revision, and fw_build...
Hello Nordic-team,
I´m currently developing an application which has been based on a 54L15DK an I´m using an overlay file for adjusting the ports to my own hardware. That...
I/ trying to read the ID of a Fijitsu FRAM type MB85RS4MT using the Nordic device nRF5340. I can properly initialize the SPI and transmit the RDID =0x9F command. The FRAM...
Hi,
I'm working on implementing a modem upload feature (using probe-rs) to be integrated into our production programming line.
Following the procedure described here ...
