Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello everyone,
I want to create a real-time wireless sensor network. There are 8 sensors in the net. I use two nRF24LE1 as receivers to recieve the datas stimultaneously...
Any idea what the max SPI slave clock frequency is on the nRF51822? The product specification (page 46, v2.0) says the max SCK frequency is 2MHz, but I was wondering if any...
Hello together,
I am searching for the source code of the MasterControl Panel for Android.
Is there a reason, that the code is not available, because the source code of...
Hello,
I'd like to know, if there is any difference between nRF51822 EK and DK, except device number. Two devices from EK will be enough for me.
www.nordicsemi.com/....
Hi,
We are interested in integrating BT MP3 player in our product and Im wondering if we can use Nordic SoC to stream audio via bluetooth to the Headset? So create an A2DP...
Hello, I am trying to develop a low power application by using nrf51822 EK board.
In " Reference manual v2.0, 11.1.3 System ON mode ",
it says there is a mechanisms can...
I am using app_gpiote_user_register() and ads_interrupt_enable() to define a ping change interrupt. When the code runs, I can see on my logic analyzer that the GPIO pin assigned...
I have a nrf51822 project with S110 (v6.0.0) softdevice. I am using latest sdk (v5.1.0). I compile the project successfully with gcc and it does run too. But I struggle with...
I'm trying to reconcile two things I read about the softdevice. The GAP roles that are supported include broadcaster and peripheral. Also, there is support for a GATT client...
Hello
I am trying to build the nAN-36 application.
The main.c file include at least two files that I do not find:
#include "ble_eval_board_pins.h"
#include "ble_stack_handler...
We're trying to implement initial programming of the chip using SWD. We can connect to the chip and successfully enter debug mode but from that point on (as per section 11...
Hi,
I'm gong to design a pcb for nRF81522 (for both packages: QFN 48 pin and 64 pin WLCSP). I coudn't find the footprint in any documents. I appreciate if anyone can send...
Hi all,
Trying to read out the nRF8001 serial number using the nRF8001 SDK 1.7 and I cant seem to work out where I should be making the call to lib_aci_get_address?
After...
I'm a wireless novice, but have electronics experience.
I'm looking to add bluetooth low energy communication from a battery powered MIDI controller to a Macbook Air (or...
