Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I am implementing SPI communication between the intanRHD2132 (ADC) and nRF52840.
I need to periodically send commands(READ, WRITE, etc.) to the IntanRHD2132(ADC) at regular...
We have a sudden problem with the flash_manager. The code stops at static uint32_t flash_area_build(flash_manager_t * p_manager), at line NRF_MESH_ASSERT(p_manager->config...
Hi.
I am designing a 4 layer PCB (0.8mm thick) for an nRF52820 microcontroller.
My board's stack: L1 - Signal L2 - GND L3 - Power L4 - Signal
I have questions regarding...
Hi dear forumers,
I'm in the goal of achieving lowest current consumption on my PCA10056 DK board, with an nrf52840.
I converted a previous zephyr firmware who perfectly...
Hello, I am using the nRF5340 Audio DK with Zephyr and want to use I2S to send audio to an I2S device. So far I have had little success with the microcontroller halting in...
11 months ago in an answer a nordic member wrote (in regards to an error that I now also had and could solve using CONFIG_DEBUG=y):
[quote userid="81283" url="~/f/nordic...
Hi there,
I have an issue when using PPKII software on MacOS at 100ksps (no issue at 1K):
The 10min button at the top does not appear anymore
After a 3min measurement...
Good Afternoon,
I'm designing a 4-layer PCB based on an NRF52832 (QFAA) paired wit h a Molex 479480001 SMT Antenna, and I was hoping for some feedback on Antenna Matching...
Hello,
I'm trying to sniff packets with wireshark by varying the connection interval and supervision timeout of my ble application. I see that with lower connection intervals...
I'm presenting an issue when exporting the data collected, specifically the digital outputs, they are exporting incorrectly, but in the Data Logger tab they are presented...
When implementing AWS_IOT provisioning by claim process, AWS_IOT responds to the published topic $aws/certificates/create/json with a 3580 byte response. This causes TLS to...
Hey, I'm pretty new to Nordic Development. I am working on nRF5340 Audio DK development board right now and I was trying to create a bluetooth speaker kinda setup using the...
Regarding the design issues with the nRF5340, I have adopted the nrf5340_qkaa_config3 design scheme from the hardware design package. However, after testing, I found that...
Hello
For some reason the example doesn't work, am I doing something wrong?
In this example, there was no overlay file, which I made myself.
I use a sensor: https...
