Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Under Ubuntu 20.04 the udp sample application that we have modified that builds with no problem under nRF Connect SDK v2.0.0 fails to build when when its directory is copied...
Hi all,
I want to evaluate the nordic ranging toolbox and compare it to a proprietary solution. First of all I set up the distance measuring example ( developer.nordicsemi...
Hello,
I have an existing application based on nRF52840 but it is using native zephyr and native MCUboot.
By 'native' i meant using the upstream versions of zephyr and...
In the Zephyr documentation, the explanation for NVS sector erase is a little ambiguous.
Elements, represented as id-data pairs, are stored in flash using a FIFO-managed...
Over the past 2 weeks the programmer fails to recognize my9160DK board. Instead, I see it listed as "J-Link" in the device list with a serial number underneath. The programmer...
Hello! I am discovering a new approach to nRF52 development. I used to be quite happy with SDK+Segger Embedded Studio. But as I understand it, this is an outdated method....
I can't figure out how to run sample code that uses the LTE-M modem.
I see nrfxlib has a modem library. But I don't know how to make a simple sample app that uses this...
Trying to build and flash the nRF5340 Audio application to my nRF5340 audio DK eval boards for eval purposes. Apparently this requires access to the LC3 repo so I am seeking...
Can you share the source impedance measurement for the nRF52840-CKAA? Is the T-network only for impedance matching? Do i need a filter for harmonics if I'm planning to transmit...
I'm using the pc-ble-driver-py: Standard Heart Rate example to read a characteristic just fine.
My issue is i now need to write a to a characteristic.
How would I do that...
Hi
I've recently been working on the ncp host example provided by nordic. after downloading the standalone version from the site, I tried programming the 2 nRF 52840 dk...
nRF SDK 17.1.0 with SD140 7.2.0
There is no example for how to use the sd_rand library. I've seen scant few posts that mention functions like sd_rand_application_bytes_available_get...
Hi I've just started developing with the nrf52840 and Ive been following the official documentation on how to use the programmer shipped with nRF Connect.
Unfortunately...
Hi,
In a custom nrf52840 board (DC/DC=on, LFCLK=RC, CONFIG_SERIAL=n), using ncs2.1.0, I measure through PPKII ~6.7uA in system_off mode, which is reasonable.
In system_on...
I have a similar question as in the previous post (about 4 years ago) with title "nRF52 WLCSP DCC routing - - ok to run over GPIO pins?" by Laserdan, i.e., I would like to...
