Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi all,
I'm using an nRF52-DK for testing the connections of pressure sensors (BME/BMP280), I tested first with arduino, and then I'm using the same code with Platformio...
Working on 52832, with SoftDevice S132, SDK 17.0.2 Our boards have external 32MHz crystal as the source of HFCLK.
Our application samples the ADC periodically using the...
I am in final stage of pre-production code and would like the associated indicator LED to go to OFF
when the coordinator is lost or powered down. I can detect it joining...
Hello!
I am struggling to configure a quadratic encoder with the nRF52840. As far as I know, the code should be working. However, when the encoder rotating, the terminal...
Hello there!
We are using nRF51822_xxac SoC with nRF5 SDK v12.3.0 and S130 Softdevice. We are kind of obliged to stick with nRF51822 because nRF52840 SoCs were out of stock...
I allowed some Windows10 updates to go through earlier today, and now I can't get my code to build.
I've even gone back to some previous versions that worked yesterday and...
Hi,
NCS for Windows VSCode have update to last,
TERMINAL panel can't copy one line,
and can't clear all.
Suggestions for improvement.
thanks
Best Regards
Toolchain: 1.9.1
modem fw: mfw_1.3.1
PC OS: windows 10
Terminal software: Tera Term
SIM card: AT&T (North America)
in the modem shell example code, in "prj.conf...
There are multiple issues like https://devzone.nordicsemi.com/f/nordic-q-a/81793/jlinkarm-dll-load-failed-on-m1-mac which are basically just « resolved » by saying « these...
Hello,
I'm trying to figure out what I am doing wrong (or what I misunderstood) about the bitrate.
According to my benchmark, it takes 1.42ms to send 128 bytes using ESB...
Hello, I'm using SFH 7072 Heart rate sensor with nRF52832 board , But i'm not getting actually heartrate, i'm getting like a 6-7 digit output , for that which calculation...
It is written in the datasheet that if i try to receive bytes more than the number i put in the maxrx register "incoming bytes will be discarded" does that mean all the bytes...
Hello,
I am working on application using nrf52810 SDK version nRF5_SDK_14.2.0_17b948a
In my application i need to read characteristics value, so after following tutorial...
i use the zephyr 3.0.9.i use direction with nrf52833 or nrf5340 in RX.The tx is nrf52833 with nrf of NCS,ITversion is zephyr 2.7.9.The default is 2us AOA. I want to use 1us...
Hi,
I have installed Segger Studio for ARM v6.22a.
I have also installed the SDK5 version 12.3.0.
I imported the IAR project project ble_app_start_notification_pca10028_s130...
