Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
My nRF Connect SDK extension in VS Code did an auto update this morning, and now my whole IDE is non-functional.
This is the error I get when I go to the Quick Setup
...
Hi,
I have made a custom board with BL5340PA module from Ezurio and i try to test simple bluetooth advertisement code but i have this error and not able to see my bluetooth...
Hello,
I am developing an LTE-M application on nRF9151, using offloaded sockets to modem, including DTLS.
Everything works great - can connect to network, and communicate...
Hi,
Our devices are running on NRF52833 with soft device version s140. We are facing an issue to do DFU in one particular device. Details mentioned below:
We are able...
Hello,
We run a Bluetooth Mesh network with about 1,000 nodes. Our master node (antenna) consists of:
· An MCU running Zephyr Mesh and keeping the CDB.
· An embedded...
Hi,
We are using the LC3 driver in our product.
We measured the current consumption with and without the LC3 driver.
When the LC3 driver is enabled, the current is 4...
Hi, I'm experiencing a significant performance drop when switching from the nRF9160 to the nRF9151DK.
I have a firmware that sends around 300 kBytes of data over UART in...
Hi, I recently upgraded my nRF Connect SDK to 3.1, and have migrated my code (which was originally based on the direction finding connectionless example) to 3.1 so that it...
Our Jenksing builds when using Nrf Connect v2.7.0, the --no-sysbuild option and CMakePresets worked just fine. When migrating to Nrf Connect v3.0.2 and using sysbuild, they...
I have some issues with the default response handling.
My Zigbee door sensor sends a message, and I reply with the following code:
```
if ( ! cmd_info -> disable_default_response...
I need to maintain and update firmware written with 15.3 SDK on an nRF52832 on Windows 11. What is the exact software and tools I need to do this. The latest Segger development...
Hello,
My use case is the exact same use case as this forum post . I'd like to run BLE and Radio Test sample on the nRF5340. The device would be in 2 modes:
- BLE
-...
Hello,
I try to figure out, how to correctly setup MCUboot for an nrf5340, so that:
Application is updatable
BT Stack is updatable
Firmware Updates are encrypted...
I am trying to enable a watchdog and then stop it. i closely followed the datasheet way to do this. the problem is that the watchdog once enabled will always fire. i want...
