Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Currently I am running one of the demo applications and have the nRF power source switch set to Vdd. The measured Vdd is 3.0V. Is it possible to change this to 3.3V? I would...
Hello
Is it posibile to do debug using Segger ES simulator for an example which uses also BLE stack?
More specific I am trying to debug the blinky example found in
...
Custom board, ncs v1.4.0, modem FW v1.2.3, SES v5.10d. The code is based on the Asset Tracker (v1), LTE with PSM, motion-activated GPS, using MQTT to send messages to private...
We are considering the nRF9160 SIP for a product we plan to develop. There is questions around whether we will need to obtain regulatory certification (Starting within U.S...
Hi,
I noticed that if you send AT+CFUN=1 then AT+CFUN=4 more than 30 times in an hour the modem stops registering until the hour passes? Is this by design?
Kind regards...
Hi,
I have built and flashed the "peripheral_uart" example on the nrf52833dk_nrf52833 from nrfconnect sdk v1.5.0. When I build using the prj_minimal.conf file, everything...
Is it possible to manually delete/inject bonding keys when BLE connecting to device with using Nrf52 and pc-ble-driver.py? I would need to execute following scenario:
1...
I have seen a compatibility matrix for nRF52840 SoC at the link below:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf52840%2FCOMP%2Fnrf52840%2Fnrf52840_comp_matrix...
Dear, manager.
Hi,
I am currently testing the use of TWI and BLE together.
However, Data (24bit) is received and read through TWI every 4ms. BLE is only initialized...
Hello,
We are evaluating SDK 17.0.2 USB MSC example.
If we connect the PCA10056 board to USB the Windows make System Volume Information folder,
so if we don't make safely...
Development environment SDK 15.3.0
I am working on overturning the saadc project based on ble_app_uart.
The input frequency is 50~2k Hz.
Terminal and debug monitor...
Hello I'd like to output two PWM alternately. Using the timer, PWM1 and PWM2 alternate outputs every 5 seconds. And I want to change duty cycle according to adc value.
...
hello,
i am using nrf52840 in our customised board and trying to interface it with GDEW0213Z16 2.13 inch display which uses spi communication i have added the necessary...
Hi,
Currently, nRF91 supports only one MIPI RFFE-controlled device. In our solution, we would like to have two MIPI devices - one pair of LTE switches as in Thingy:91 for...
