Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi Team,
I have gone through many threads on the forum but still in doubt regarding how to interface nrf52 over HCI to the Linux based host.
My understanding is currently...
When building example ble_app_interactive_s132_pca10040, SES asks for missing "nfc_t2t_lib.c" and "nfc_t2t_lib_al.c" files. This happens when SES is 'Preparing target for...
Hi,
I'm currently trying to use 2 channel SAADC to measure 2 analog input port
I've searched other questions in this forum and referred SDK example
Actually, I could...
Hi All,
I want to measure the battery level in my nRF52840 design using the ADC.
I came across this thread in the nordic devZone https://devzone.nordicsemi.com/nordic...
Hey all, I am bit late to the party but I was following Vidar's HX711 Library and was able to configure it to work after a long period of time (Pardon me, I am new to this...
Hi
I do NOT know how to read log messages doing run time, is there a terminal window you Can use. I use Windows and have a nrf52840 and write code in segger embedded st...
Using oneWire library, I was able to get the temperature from the ds18b20. But it didn't work if I put the same code in the Beacon software.
I understand that the softdevice...
I observed that the asset tracker application will not run using code starting with commit a507a3e42229544b195e93a9896ca09c8a4fba85 and newer, on the master branch, in repository...
Hi,
We have been working with a coordinator and a router device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
I have a binary file for a 3rd party device that the manufacturer has asked me to test on their devices. I have looked through the ZigBee OTA example documentation but it...
Hello:
I am working on a USB bootloader where I have enabled the WDT on entry. After I enable the WDT, the app_timer is set to feed the WDT and to also signal the end of...
Hi
I have a new Thingy:91 that I'm updating.
After I updated the modem software and the firmware with Connect desktop Programmer.
When i could not connect I deleted...
We recently had an issue where a race-condition was caused because we handled entry to sleep mode a bit too carefully. Therefore, I wanted to discuss different methods to...
Hello!
USing help from this forum i have successfullz transmitted adc value from one pin of AIN# to ble and reasing values successfullz but now i am facing an issue that...
Hi Nordic Team：
I use version is: nRF52840 DK Version：nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\thread\ncp\ftd\uart\hex
Raspberry Pi 3 Version：RaspPi_OT_Border_Router_Demo_v4...
