Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
I have been using UART0 to implement a very simple console using console_getline_init() and console_getline().
So the nRF5340 receives commands over UART0 and outputs printf...
We're building a cryptocurrency hardware wallet. And we're using the secure bootloader provided by nrf5 SDK, to only upload signed firmwares to the device. We are using nodejs...
Hi guys,
I am working with nRF52832 board and Zephyr for a short period of time and I really don't have to much experience. Every day I learn some new things and try to...
Hello,
We have a custom board of nRF52832 with two buttons and right now Buttonless DFU is also working perfectly. But, we have scenario where if combination of two buttons...
Please help with writing to flash. If SoftDevice is off all ok. If SoftDevice is enabled, the sd_evt_get function always returns the value 5.
Here is the test code:
Hi!
We are developing a tracker based on Thingy91 using GPS and LTE. We're using the latest Modem firmware 1.2 and Zephyr/NCS v1.2.0
The GPS cold start until receiving...
Hi Devzone!
I'm trying to monitor the battery level of Lithium Ion battery.
I'm using SAADC to check the voltage of 3.7v 3500mAh Lithium Ion battery.
The battery...
when I am waiting for an event the current consumption is becoming ~180uA continuously.
I am waiting for an event using the following function
void deep_sleep(void) {...
Hi All,
I would know, is the NRF52 BLE Mesh Bluetooth 5.0 qualified or not. I did not find it anywhere. As I can see the in Cypress website, they clearly mentioned that...
Can somebody please measure and post the dimensions of the nRF9160 DK please.
Either they are not in the SPEC, or i cant find them.
either way W x L x H - would be appreciated...
Is there a way to specify which AIN should be used through the devicetree API? For example, here is a code snippet:
How would I use the devicetree API to replace the NRF_SAADC_INPUT_AIN6...
Hi
regarding the Nordic guidelines for aQFN, it recommends to use 0.305/0.61 for through hole via.
We are using 0.2/0.4 to avoid soldering bridge and non find any issue...
Hi,
I've tried the Heart Rate sample code (both from hex and source file) and in both cases, I encounter the same problem - constant disconnection. When it finally connects...
Hey, so I have been working on developing a BLE central device on a Raspberry Pi using the bluepy library. It's a pretty simple application, I just need it to scan and interface...
I tried to launch your example "Bluetooth: Mesh Light" using nRF5340 PDK and I failed. I followed this guide developer.nordicsemi.com/.../README.html . Also I tried to launch...
