Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
In working through understanding how sleep works with the SDK I ran into the following note for sd_app_evt_wait()
The application must ensure that the pended flag is cleared...
Hi. I'm trying to study nrf52832
but, APP_TIMER do not work.. what should i do?
(1)
mcu : nrf52832
sdk: nRF5_SDK_15.2.0_9412b96
(2) setting :
> sdk_config...
Hi,
I'm supplying a DK with an external battery source plugged into J6 (Li-Po) and the nRF power source switch set to VDD. When I flash the chip with one of the Openthread...
I am attempting to scan for BLE devices using ble-sniffer_win_1.0.1_1111_Sniffer and the nRF51 Dongle. It begins scanning for devices then the window closes.
I am running...
Hello, I am trying to use SAADC with nrfx APIs and the ADC does not execute the conversion, and the callback function is never called.
Here is my code:
I am using also...
Hi,
I am using 15.2.0 SDK and 3.0.0 Mesh SDK for development.
On the Nordic nRF Mesh App, we made certain changes to the generic level slider such that it send out live...
Hi, I am using Heartbeat messages with the light switch example, and want to log the nrf_mesh_rx_metadata_t in heartbeat_opcode_handle() to RTT viewer so I can write it to...
Hi,
if my device (nrf52832) is in application and I perform firmware upgrade using nrf connect and PCA10031 on Win 10, the upgrade process is very slow (0.35 kB/s). I stop...
Hello,
I have a following requirements,
Build a custom bootloader which accepts DFU through OTA and UART.
this boot loader must also contain softdevice , so that finally...
I'm having problems with toggling the EXT0 pin on my thingy:52.
I have tried with setting the EXT0 as an output like this: drv_ext_gpio_cfg_output(SX_IOEXT_0); And then...
This is not really a problem - more like an enquiry
Is it possible to gate PWM output using another GPIO pin e.g. if the second pin is low then so its the PWM otherwise...
Hello,
I would like to test and adapt the example "ble_app_uart_coexist" with my nRF52840 DK. Unfortunately, I believe that this one is only intended for nRF52832 and softdevice...
Hello,
I am trying to use the BMD-350 evaluation board to program a standalone BMD-350 module on a custom PCB. I have followed the instructions in the documentation to connect...
Hi,
I'm using custom board with the nrf42840 and I need to use p1.09 as a GPIO.
How can I do this in a debugging mode (using the PCA10056 as a jlink)? Can I get a code...
Hi,
I want to get interrupt on GPIO using gpiote module.
I searched for example but couldn't get it.
Can you guide me how to use gpiote in nRF9160 ?
Regards,
Smitesh...
