Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I have a case where the receive end event is triggered even though the receive base address and prefix shouldn't match. Some background:
Initially the receiver is...
I am working with the nRF51822 S110 and having trouble implementing SPI. In other devices' SPI protocols, MISO can be held high until the device is ready to transmit data...
I'm uising the NRF51822 PCA100001 eval kit. I'm trying to open a couple uVision 4 projects in uVision 5. Unfortunately, it keeps telling me to install the software pack. I...
Hey,
I am designing a custom PCB with the nrf51822. I would like to use the reference layout that Nordic provides, specifically nrf51x22_qfaa. My project involves reading...
I have recently started using the new rev 3 parts with 32K of SRAM and I was wondering what the timeframe is for the softdevice to take advantage of the extra memory?
My...
I would like to understand when I would need a wired programming (with help of TC2030 connector) interface and when I would need OTA. I am trying to find the easiest and fastest...
Hi,
What is the difference between using WFE and sd_app_evt_wait to force the processor into sleep mode?
We're trying to optimize for power consumption, and somehow...
I have experimengted with prepared write on Nordic 130 softdevice and found it's quite
low performance in terms of throughput.
First, between iOS/Android device and Nordib...
Hi Nordic's experts
We got a RF problem in certification test, attached picture is the measured occupied bandwidth, the value of OBW is 1.73MHz , but the guy in the lab...
Hi,
Does anyone known what the maximum frequency is that the timers can operate on ?
I want to count a signal that is 24Mhz while the clock frequency is only 16Mhz.
So...
Hi :)
In my program, just ONE pipe to use advertising service data is not enough. There is the function:
lib_aci_open_adv_pipes(const uint8_t * const adv_service_data_pipes...
Hello,
Sorry for this newbie questions.
I have a side project (connected device) that will need a BLE component for communicating with phone apps (android, iphone). I...
Hello, everyone
I am trying to let our nrf51822 board transmit data automatically after the cccd modification. I have been use the Master Control Panel to do this. For example...
I'm using the PSA1001 eval board with SD 110. The device comes up advertising, I can connect and access my services. I need to the Central to be able to issue a disconnect...
Hi.
We are doing a few test on the S120 range with the Softdevice v1.0.0. We have a peripheral device that we can scan and connect it with iphone within 50-60m. However...