Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
How can I retrieve the complete list of supported input and output clusters for all endpoints on a Zigbee end device? I'm currently able to access the On/Off cluster...
Hello,
I'm trying to use several USB CDC ACM instances with USB_DEVICE_STACK_NEXT. (nRF Connect SDK 2.8.0)
Is there a way to set the VID?
And is there a way to set different...
hello, when trying to program my 9160 board, I get this: I already tried the recover command but that yielded the same results. thanks in advance -shlomo
Hello. I have a question about setting the VS code development environment.
" ">www.youtube.com/watch I installed the above YouTube link and installed toolchain v2.8.0 and...
Hi,
Is there any low power mode option for nRF91xx devices where it can still retain could connection? Can this be achieved through iDRX mode?
Regards,
Pavan Vo...
These are customized UUIDS declared by me
/* Custom Service Variables */
#define BT_UUID_CUSTOM_SERVICE_VAL BT_UUID_128_ENCODE ( 0x821675c3 , 0x4046 , 0x45f9 , 0xb8df...
Hello,
I am having some problems with sending data packets larger than 20 bytes over BLE.
We are currently updating our product, that includes the nRF52832 on a custom...
I have an nRF7002dk & its datasheet mentions that there is a 64 Mb external flash memory. The memory is connected through a regular highspeed Serial Peripheral Interface ...
Hi! I'm using the nRF9160 DK where I am aiming to send over bluetooth device count that was picked up from the nRF52840 on board to the nrf9160 on board via UART. However...
Hello,
We are facing an issue where the sum of count in BLE_GATTS_EVT_HVN_TX_COMPLETE events (member of the ble_gatts_evt_hvn_tx_complete_t structure) doesn't match with...
Hi all:
when I develop with nrf54l15dk and nrf connect sdk v2.8.0 on macOS.during flash my dk board, it show me the info as below:
But, I tried flash my board with terminal...
HW PROBLEM 1 First of all, it seems that the board has some HW issues: when I plug in the USB in the IMCU USB to use the on-board J-Link, the chance of the board booting up...
Hello,
I have failed to get the I2C working on the nrf54l15dk, i have now connected it to a oscilloscope with pull ups.
i have confirmered the pull ups work, but as i...
I made a custom PCB with the NRF52840-CKAA and the same 8MB flash memory chip as the PCA10056 NRF528040DK
I used the MX25R6435FZAIL0 because the MX25R6435FZNIL0 was not...
Dear Nordic Team,
After gaining experience with 3G and later 4G LTE-M over the past few years, I have observed a significant gap in the deployment of LTE-M in many countries...
