Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hello:
I have a problem here:
Connecting ... - Connecting via USB to probe/ programmer device 0 - Probe/ Programmer firmware: J-Link OB-nRF5340-NordicSemi compiled Apr...
Hello everyone,
I am planning to use the nRF9160 as the main microcontroller for my project. Alongside this, I need a Bluetooth module to transmit data to a mobile phone...
I'm using an nRF52840 as BLE peripheral with a custom service similar to NUS to send large data. The data is send in 4k chunks via BLE notifications to an Android phone. With...
In the nrf5340 Product Specification, the GPIO registers OUT, DIR, LATCH, DETECTMODE, DETECTMODE_SEC, and PIN_CNF[n] are all labeled as "Retained Registers". The definition...
I have had luck setting up signatures using MCUBOOT and sysbuild. However, I have not been able to encrypt the images. sysbuild.conf: SB_CONFIG_BOOTLOADER_MCUBOOT=y SB_CONFIG_BOOT_SIGNATURE_KEY_FILE...
I have a product that uses the nRF5 SDK that I do not plan to migrate to the nRF Connect SDK. My product uses ocrypto 3.0.8, which shipped with the latest version of the nRF5...
Hello,
I have an NRF9160DK board and a custom board running the SLM application that are exhibiting similar behaviour. Both boards work fine with the supplied iBasis SIM...
Here's a weird error, that started happening seemingly overnight: paths being parsed wrong on windows due to path separating backslashes being interpreted as escape sequences...
Hi,
I have done some searching and cannot find a direct answer to this. I have a gpio pin defined in a custom device in my board dts. I want to set this pin to high drive...
Is it posiible to use bt_disable on the nrf5340 board? for some reason it doesn't work, returns and error on this line:
if ( ! bt_dev . drv -> close ) {
return - ENOTSUP...
Hi all,
I need to modify the app.overlay dts overlay in mcuboot to be able to see the printout, among other small details. I was able to change them in the "C:/ncs/v2.5...
I'm switching from STM32 to nRF52840 and it's for a battery-operated device that only wakes up every few hours and only stays awake for about 10 seconds. With the STM32 (and...
One of our products uses the NRF51822 for Bluetooth communication.
This product is now undergoing CE certification. Is there a CE DoC (Declaration of Conformity) for the...
When creating a new board in the nRF Connect VSCode IDE, and just entering the basic items for name, if trying to use sysbuild there is a CMake error. I used name "foo" and...
I'm running Windows 11, have the kit connected with a microUSB cable and it shows up as a properly working nRF device on COM5 in device manager. I'm using v5.0.2 of nRF Connect...
