after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hardware: nrf7002_nrf5340 Version: ncs-v2.61 Firmware: sample/aws_iot + BLE Mesh initialization ( chat_cli sample example ) Scenario:
My project requires BLE Mesh and MQTT...
Now I am using the https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/direction_finding_central/README.html and https://developer.nordicsemi...
Dear Nordic Team,
I had questions concerning the use of the High resolution oscillator
Question 1 :
Could you provide the detailed step needed to enable the HFXO ...
Hello guys,
I'm trying to clearly understand the Bluetooth Peripheral Sample github.com/.../peripheral_uart and how it exactly works.. so i'm curious if there are some...
Hello, I would like to ask about the problem of how to implement SOC shutdown in NCS. 1. In V2.6.0, CONFIG_PM cannot be enabled, it will prompt that there are dependencies...
Hi there!
I was just trying an example of DFU over UART from the new nrf Connect SDK Intermediate course using the NRF9161DK but I'm unable to disable the mass storage device...
Dear sires,
Would it be possible to let you answer the following question?
In nRF5340 SDK, does it use CMD20"SPEED_CLASS_CONTROL " in SPI write sequence to ensure minimum...
During some operations like factory reset, or during a hardfault we want to check if the softdevice is enabled and disable it if it is enabled before continuing with further...
Hi,
I want to use BLE mesh to reach my application, the requirements below.
I have a root node and need to send the custom data to each client node and need to read...
Hello! I was building a custom board and tried to build the project for my board but it gives an error: === child image hci_ipc - CPUNET begin === loading initial cache file...
My understanding is that Singled-linked list built in to zephyr... https://docs.zephyrproject.org/latest/kernel/data_structures/slist.html But, I don't quite understand how...
Hey I've got this project that requires two buttons. In normal mode, these buttons react to the Ready pin switch signals. when it goes into sleep mode (where it controls other...
I am using ESB communication.
In general situations, data transmission works well. However, issues arise when multiple PTX devices transmit simultaneously.
It's understandable...
Hello,
I use Nrf52833DK running nRF Connect SDK (NCS)
I want read and write BLE MAC device address no matter it's the public one or static one.
Now i know bt_read_static_addr...
