Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
I have the launch.json as shown below so that I can attach the debugger to a running image. This works with Cortex Debug. However, when using nRF Debug it does not seem to...
hi,
I'm using nrf connect sdk to communicate spi sensor.
which is better choice to use SPI in ncs (nrfx driver or zephyr ) ?
i) nrfx_driver: nrfx_spim_init(&spi, &spi_config...
We are trying to read a flow sensor in our device. The device is in PSM mode most of the time.
The sensor outputs its state in digital mode HIGH or LOW. We are checking...
Hi, I have developed some projects on nRF52840 DK pca10056. I want to program/debug the nRF52840 chip ( this chip ) with SEGGER J-Link debugger/programmer ( this debugger...
hi team,
i am using nrf52840 controller,i have few queries related to how ZYFER RTOS used in this controller.
which of below process is correct,
1. ZYFER RTOS image...
Hi,
Two questions regarding internal temperature sensor
Internal temperature sensor conversion time ?
Internal temperature sensor current consumption
Could you...
Hi,
I have a NRF52840 and a bluetooth device. Is there a way to automate the communication by writing/reading the HEX code. It is essential for product testing. Example...
Hello,
I am trying to figure out which example is the closest fit for our design. We are using a 2 processor solution in our product, and the firmware for the NRF52832 has...
Dear Nordic Team,
i need to develop an nRF52 beacon custom pcb.
Do you have any tipps or better altium files for creating a low-power electronic board, powered by a CR2032...
Dears all,
When a bluetooth mesh node is done provisioning and added an appkey, I want to bind that appkey to local models.
I could not find any API for that.
Can you...
Hi, I use nRF52840 DK to run PTS test.
It's fail at L2CAP item.Correspond message is "Failed to create L2CAP LE Credit Based Connection".
How to create "LE Credit Based...
Hello!
I've been investigating NCS for several days and come to the conclusion that we don't definitely have to use it for our developments. By the way, it'd be way too...
Hi,
I have a custom board with nRF52832 with external spi flash and I'm using SDK 17.1 and softdevice s132 4.0.5. I will use OTA-DFU to receive the new firmware image from...
