Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Dear ,
I am currently testing the UART peripheral on nRF52832 and nRF52840 using nRF Connect SDK.
Basically, I have a sensor that continues sending out data via uart and...
I'm trying to build the pc-ble-driver ( https://github.com/NordicSemiconductor/pc-ble-driver ) to be able to use the nRF52840 as a receiver for a thermometer. See https:/...
I have a custom board with NRF52833 that I'm unable to flash or communicate with using JLinkGDBServer. I was hoping for some help understanding the errors seen in this log...
Hello Nordic team!
I had a post where I verified the answer by misclick: https://devzone.nordicsemi.com/f/nordic-q-a/83749/nrf52-dk-as-central-to-discover-services-on...
Hello
I'm using nRF5340 DK with nRF Connect SDK 1.5.0 and SES IDE and I want to change the PHYs and TX power of the peripheral_uart sample ( v1.5.0\nrf\samples\bluetooth...
Hi,
Based on peripheral uart sample code on nRFConnect SDK 1.8, I'm developing a custom BLE application under nRF5340 using VSCODE though nrfConnect extension.
In order...
I tried to program this example developer.nordicsemi.com/.../README.html onto the nRF5340 network core, following the instruction from here devzone.nordicsemi.com/.../ncs...
Hi,
I am new here. I have a very basic question, maybe bordering on Dumb.. but couldn't see the answer in previous questions.
My board will normally be working on AC power...
Hello,
I'd like to remove the "configurations" in Segger Studio and the associated extra directory level; I consider them counter productive.
So how can I get rid of those...
Dear Sir.
A timer is defined for 1 hz,
Every 3 minutes or so we drive the buzzer with different pulses ( see code attached )
We are using the PWM to drive a buzzer...
error repported segger
39 minutes ago
Online lm
47 pts.
Hello, i'm trying to flash a code in my module nrf52805 thx to my Dk nrf52840. i have this error I...
Hi team,
I'm streaming the sensor data through USB (using hterm) every 2.5ms.
i have configures USB as CDC and using virtual COM port.
In each iteration, i transfer...
i have nrf52832 using nrf sdk version_17 and s132.
I have application for logging
i have followed steps:
1). intially device in sleep mode
current: 0.35 micro Amp...
Hi,
I am working at a project that was abandoned by a guy that worked on my position. I have to fix some issues and add some features. I'm using SDK 17.0.2, my IDE is VSCodium...
Dear all,
I am now using two nrf52840DK and nrf connect sdk v1.7.1,and I want to send packet using llpm mode between two devices,one is receiver and the other is sender...
