Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello, I have the custom design. Schematic is below: I use Visual Studio Code and nRF Connect SDK V1.6.1. My programer is NRF52833DK I used example code (zephyr/samples/basic...
Hi,
We used the nrf52840 in our first release of our project. And we decided to upgrade to the NRF5340. We already have port our software to the Zephyr OS on the nrf52840...
My question is very similar to If I use nrf Connnect SDK 1.6.1 and Zephyr, which Bluetooth QDID should I use?
Following this case I need Zephyr Version 2.2.x and can use...
Hello.
We want to mass programming the nRF9160-SICA in our production IC only - NOT soldered on a PCB.
Is there exist any IC connection adapter for this IC that can...
Hi, Request confirmation that nCS nordic SPIM & SPIS drivers implicitly use DMA, I found the response as in: https://devzone.nordicsemi.com/f/nordic-q-a/83593/zephyr-rtos...
Hello! Does anyone know how to access the source code installed on the nrf52840dongle with the Bluetooth Low Energy application?
As you can see, the application offered...
Hi,
I need to enable PIN based security for my dev. project on Nano 33 BLE, by PIN security I mean force mobile app to enter a hard-coded PIN to connect to my BLE device...
Hi,
I'm working on a simple app that is supposed to generate a CSR and have it signed by a web server. The problem is, I can't even get zephyr to build the components...
Hi,
i am working with ic nRF52832_xxAB. example provided is based on nRF52832_xxAA. creating ram size issue. how to select proper ic numer, flash and ram sizes.
Hi,
I am currently working on a custom flex board using the Taiyo Yuden EYSHCNZWZ (based on the nrf52832). I am able to program the device with the soft device, bootloader...
Hi,
I'm designing a PCB based on the nRF52 Dev kit.
I just need a BLE module with the nRF52832. My question is if I use the ports p19 or p20, do I really need the ATSAM3U2C...
Hi
I am trying to write 200bytes of data in flash memory ,
but sd_flash_write() returns error code NRF_ERROR_INVALID_FLAGS.
and i couldnt find out the reason for that...
Hi
I wanna use second pin of nRF52832 as a gpio output pin.
I'm using software as a follows.
・nRF5_SDK_17.1.0_ddde560
I don't know which function programs I must use...
Dear, 1. what maximum voltage may be applied through the two pin connectoe marke External Supply on nRF5340Dk kit? 2. Does the Debugger works with external supply also or...
Hi,
Simply asking, what is the difference between nRF Connect SDK and nRF Connect Desktop? I would like to program nRF5340 DK with a feature of ble coded PHY (ble with...
