after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I was wondering in Bluetooth mesh, which layer defines the Relay, Proxy, Friend, and the Low Power features for nodes? For example, is it done by the application, Link layer...
Hi there,
I have nrf52833dk and i have implemented the direction finding examples from nrf connect sdk. kindly guide me about antenna hardware setup that i need to do with...
Hi,
Please excuse me if I ask some stupid questions I am new to wesr and have only used git simply over the last few years. These questions stem from trying to get percepio...
Hi,
I'm designing my own algorithm for direction finding and for that i need IQ value as input. In NCS v1.6.0, in the locator exemple for aoa, the IQ value are store in...
hello,
I'm using SPI in NRF52840 with sdk16, In Nordic Dev zone forum I have read that we can configure frequency of SPIM3 up to 32 MHz but in actually as I can see there...
Hi All,
I am trying to make a project for RGB lights using nRF52-DK using NCS.
In these lines of code I am getting the following error -
'DT_N_ALIAS_rgb_pwm_P_ch0_pin...
Hi All,
wondering if anyone else has experienced this. I'm currently developing a program based off of the ble_hids example in SDK17. Currently I'm using the app_timer...
Hi All,
Setup:
SoC: nRF51822
SDK: 11.0.0
Softdevice: S130 2.0.1
I am facing occasional HardFault and It is happening randomly. I need to test device few hours...
Hi Team,
I am trying to perform firmware update of nrf52840DK using MCUBOOT bootloader over UART. I have followed the link: https://devzone.nordicsemi.com/nordic/nrf-connect...
Hello everyone,
How can I use rand() and srand() functions in NCS?
I have already #include <stdlib.h > , but I got this issue:
undefined reference to `srand'
Thanks...
Hi Team,
I am facing the problem while adding static library (.a) file to the segger environment project. If this added successfully then I can easily access the function...
I found that there is no project or example of FTD for nRF52811 both in "openthread/ot-nrf528xx" and "nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8"
I want to know that...
Hi,
I bought two of the NRF52840 Dongles to learn and develop smart home compliant applications running on ZigBee protocol. My goal is to create a Smart Home ZigBee hub...
Hello, i would like to interface nrf9160 DK with an rfid reader mfrc522 using SPI. So, i went through the example of spi_master in SDK 8.1.0. It was for nrf51822 and i want...
Hello Nordic support,
I would like to know how can I use the function zb_zdo_mgmt_permit_joining_req() to make the coordinator start the permit to join process forever....
