Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
I'm having some difficulty debugging an issue with the mqtt library on the nrf9160dk.
I have written my own Cmqtt library class that wraps the Zephyr mqtt library...
Dear ,
On Windows 10 Bluetooth add a device,
Why SDK_17_0_2 Example does Bluetooth be disconnect immediately after pairing
(Use about \nRF5_SDK_17_0_2\examples\ble_peripheral...
When I open the Light Bulb project in Segger Embedded Studio I see a bewildering list of project items. I pick the first project, 'zephyr/merged.hex' and right click to set...
SDK: 4.1.0
CHIP: 52840
Hi, I have developed sleepy zed. It lost the connection with the network after joining in 1~3 days.
It assumes that the zed couldn't get the...
Hi, guys.
I'm using nRF52 DK (PCA10040). After I used Zadig (Driver setup for J-link), I cannot build and run my previous code to the nRF52 DK anymore (see the first 3 images...
Hi
I am using nrf52840 boards and by using the coexist program I am able to send and receive messages through mesh while using the ble services.
I followed the instruction...
I use NRF52DK as central device I also use a SDK that is ble_app_uart_c code for my project. and i would like to take my peripheral devices whice are phone or PC their RSSI...
Hello - we're using "nRF Connect" from the Apple App Store for the development of our project.
First, thank you for making this tool available and free for everyone to use...
I am using nrf52840 via NRF Connect and Zephyr configured to use the Nordic SoftDevice BLE controller.
My use case is for a central to sample a rapidly changing real-time...
As a beginner,I’m sorry for asking such a stupid question,but it has annoyed me for a long time.
I built and downloaded the program to my DK,and I used PuTTY to connect...
Hello,
I've designed a pcb using the 52840 chip which is essentially identical to the dongle design. My intent was to use the firmware that comes pre-installed with the...
Is there a set of prj.conf settings that I can use to redirect the AT command interface to the RTT debugger? Would be nice not to have to hook up a serial connection.
Hi All,
as the title say I'd like to know if is the Wake on GPIO available for nRF52840_dongle and what is the I OFF_RAMOFF_GPIO ?
My application should behave more or...
Hello. I'm developing a project using nRF52840. I've been working with the nRF52840Dev Board and I have a BLE project that runs there. I'm developing in Segger IDE and using...
When building a product which has multiple models but the firmware is essentially the same, perhaps with a few different parameters, I want to use the same code base and have...
