after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi Dev Team,
I am using the mqtt_simple example to publish my data out every 1 hour. I tried the example and it is working well and I was able to test it via MQTT.fx with...
Hi,
Is it somehow possible to plot data comming from external target board with nRF52, connected to nRF52 DK via swdio and swclk lines, by some data plotting program? Etc...
I am using NRF52832 for BLE application with softdevice 132 under SDK15.3. My application is supposed to sleep off after certain amount of time when there is no user activity...
I am using two SAADC channel on nRF52 DK, one for pressure sensor and another for battery level. I realized 0.5mA is higher than single channel. Is it normal?
We need to develop a portable device，In order to save cost and low power consumption.We need to know how to make nrf52832 connect to the Internet through the Bluetooth network...
I wrote a program to toggle the pins of P0 and P1.
When I write:
P0=0xff;
P1=0x00;
Only P0.0 - P0.3 are high and P0.4 - P0.7 and P1.0 - P1.6 are low.
P0=0x00;
...
Hello,
I am talking about nRF5_SDK_17.0.2_d674dde/components/libraries/log/src/nrf_log_frontend.c.
In the case of HEXDUMP there seems to be some inconsistency in the packet...
Just downloaded this (5.10d) on MacOS 10.15.7.
(Planning to test with 9160 DK.)
Using getting started assistant
Got as far as the "setup a project in SES" (installed...
This is our 4th nRF52840 DK this year that got damaged this way. After using it for 1 to 2 months the DK does not work power up normally. Then we can only use the board with...
In RADIO - 2.4 GHz radio TXPOWER register say:
"When the radio is operated on 1.2V, the output power is increased by 3 dBm, i.e. if the value -20 is specified, the output...
Hi,
We are having some EMI issues with USB full speed and would like to force the nRF52840 USB controller to operate in USB low speed mode. Is it possible to configure the...
Hi
I use the following script to program my boards which takes 20 to 30 seconds to complete. But recovery and programming done through SES for the same code is much faster...
I'm using nRF51 BLE dongle as a sniffer and trying to capture BLE packets through CLI. I'm using example.py which came with nRF sniffer software.
I unable to get the list...
