Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hi,
Could you confirm that DeviceID found in FICR of nRF9160 is:
1/ randomly generated (64 bits = 8 bytes)
2/ they are not unique, but already on the chip when it...
Hi,
Greetings!
We have successfully checked DFU application from SDK16.0.0 and it works nicely.
We have used android nRF connect app for firmware updating.
Here we...
We have been supplied with a module that sends SpO2 data but it uses 8bit, plus odd parity. I have seen the many questions on this subject and only pose this question to add...
To be able to have USB communication/interface, do I need to apply 5V to VBUS? Or will 3V on Vdd be enough. I am planning to use coin cell that is max rated for 4.2V so it...
this is my code on DFU function, I copy to the example of experimental_ble_app_buttonless_dfu on SDK12.1. I used nrfgo studio to program s130_nrf51_2.0.1_softdevice , boot_setting...
Hi,
I've been working on Thingy:91 under ncs tag 1.2.0, trying to develop simple application using NVS just to see how it works. Based on the zephyr sample I wrote the following...
Hi:
i have some problem about using ble.
in my application has a loop:
1.use ble adv,and Wait for a while,
2.close ble adv ,and using base radio funciton.(do stop...
Hi
I was able to successfully complete the RF output power measurement using nRF52840 DK with the help of Nordic devzone last time.
Based on successful measurement...
Hi,
I use proprietary service to transmit data between raspberry pi and nRF52840 DK. The example I referred to is below.
C:\nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral...
On the nRF52840, I know the PPI, and therefore any events/tasks, are synchronized to the 16MHz peripheral clock. Here is the quote from the documentation:
"On each PPI channel...
SDK:SDK15.3.0
Example: ble_app_buttonless_dfu project.
MCU : nrf52810
SD: s112
Hi,i want to know how to reduce the ram consumption on nrf52810 sdk15.3.0 ble_app_buttonless_dfu...
My program loaded to a nRF52840 DK unfortunately adresses ports P1.15 and P1.13.
Now the DK is not reachable for Segger IDE and can not be found as a USB device.
I can...
For the connection (peripheral) tab of the online power profiler, I have a question on why if my TX payload is 216 bytes which fits within the LL PDU size, the payload would...