I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
We are writing SPI drivers for RF chip and blocked on the below issue. The issue we are facing is the Chip Select line is not active(active low) until the TX transaction is...
SDK: 12.3.0
SOFTDEVICE: s130_nrf51_2.0.1_softdevice
CHIP: nrf51822 AC 256K flash 32K ram
GCC flags:
# C flags common to all targets
CFLAGS += -DBOARD_CUSTOM
CFLAGS...
Hi,
I want to write or change the code in to nRF52832
I have some code this code i should write for nRF52832
kindly give any suggestion
here is the my code
uint8_t...
Hi everyone ,
I have a custom PCB using nrf52840 and i measured the current consumption using PPK(power profiler kit) . The sleep current value that it show is 4.5mA.
...
Hello,
I want that two devices can connect with each other and only each other . To do this i wanted to use whitelist on peripheral side but i found that i could use filtering...
Hello.
I'm using nRF SDK 15.2 together with the Nordic 802.15.4 driver ( here ).
When trying to add the libuarte module to my project I started having mysterious issues...
Hi there,
I'm trying to get a one button nrf52832 device to behave like the following:
1. Button press short: RESET or WAKE (depending on POWER state)
2. Button press...
Hello,
I got problem when I press button program go to interrupt mode, but than all stops because of vektor catch. Im using ble_app_uart example.
Here is my main function...
I guys, I m trying to use the nrf52840 protocol in order to send an interrupts between two boards.
Looking at the examples provided in the SDK i didn't understand how to...
Hi, I have a particular issue that happens intermittently, I was hoping someone here has come across the same issue and possibly knows how to fix it.
My Setup:
Using...
Hi
I am trying to add manuf data to ble_app_hts sample advertisement but without success:
static void advertising_init(void) { ret_code_t err_code; ble_advertising_init_t...
nrf52840 last version of SDK Hello I need help. I want to start ble_adv and then stop with a button signal and start again with another button signal. The idea is
Loop:...
Hi,
I am using ble_app_uart example and want to detect the read evant/ call back. Kindly help me how to register a call back function of a read type characteristic. I want...
Hi all, I'm working on nrf52832 in segger embedded studio. Using ble scanner app, I'm entering some random values. So when i enter a value, I'm adding them to watch and checking...
