Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
How to calculate the free Ram and Flash after I loaded bootloader + SD + App on a running nRF52840?
I want to know ways to measure during critical RAM load too.
...
Hi, what is the correct way to erase all the connection params of a zigbee router device (not coordinator), and restart to search for a network automatically in production...
Hello,
I am using SDK 15.2.0 ,nrf52840. In my application we are using bluetooth and USB. The application works good. The device advertise and can get into the application...
Hello,
I have SDK v15 and there is not much information in infocenter also about these two functions related to my doubt.
( NRF_PWR_MGMT_SHUTDOWN_GOTO_SYSOFF & nrf_pwr_mgmt_run...
Hello, I'm starting evaluation of the Mesh Light Switch Demo both on DK PCA10056 and on Dongles PCA10059. I 'm using SEGGER IDE and made sure to properly set target in Preprocessor...
Hi , i tried to modify the template example from the sdk 15.3 but im getting an compilation error from " nrf_log_backend_rtt.c"
SEGGER_RTT_Conf.h: No such file or directory...
Trying to up load mqtt_simple sample, however getting bus fault on terminal. have browsed after the same issue here, but don't work after doing git pull ect...
here's...
How to correctly reinitialize the BLE stack when using FreeRTOS?
I can not find in the libraries where the task for the work of the stack under FreeRTOS is created.
Stopping...
We have a connection between our nRF52832 (server) and a tablet (client). We're trying to transmit some data at a rather high throughput. The connection parameters are as...
Hi everyone,
I have a problem with my custom nRF52832 hardware. I soldered my prototype hardware and then I checked if it is correct by checking debugger SW device settings...
Hello,
I'm trying to get as much throughput as possible using the Coded PHY. I noticed that apparently the Data Length Extension feature is not supported together with the...
Sometimes, i found that my firmware still at the old version after update complete, there is no any error.It same happen on use Android-nRF-Toolbox to update firmware.
code...
Hi, I am interfacing external memory chip that is based on SPI protocol with nrf51822. I have to read more than 255 byte via spi in single buffer with 4 byte of command. Even...
Hello,
I am using a custom board with nrf52840 using SDK 15.3 and ICM 20948. I see a lot of twi drivers and its confusing which one to use. I want to read the ICM 20948...
