Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
In our product we have implemented buttonless DFU over BLE with the secure boot-loader (unbonded) on SDK 15.2. The bootloader is unmodified except for the addition of PA/LNA...
When I compile the program times an error :
.\_build\nrf52810_xxaa_s112.axf: Error: L6366E: uECC.c.o attributes are not compatible with the provided attributes . Object...
I am trying to run the SPI code on an NRF52382 based custom board. I am using the NRF 52 DK, Keil uVision 5.0 , SDK 15.2.
I cannot set and clear the SPI relevant pins...
I am evaluating the nRF52840 for developing wearable tech that would implement some basic sensors such as GPS & pedometer. Just have a couple questions regarding the transition...
Hi all,
I am sorry if this is a rookie question. I had researched and tried the methods shown online, including:
added $(ProjectDir)/flash_placement.xml to the linker...
Hi
I am working on nrf52840, try to create a service,so i follow the tutorial , but i got a problem. The DK doesn't advertise, when I debug it, then it will jump into this...
Hi,
I manged to successfully run the mesh DFU example, however i noticed one unusual thing. I was expecting device to revert to old version of firmware, if in case the...
Is there an example somewhere to show how to use the "BLE_APPEARANCE_GENERIC_HID" to transfer data over BLE to a another BT device such as a laptop ?
The HID mouse and HID...
Hi,
I have a use in mind for a Nordic part, probably the nRF52810. It would be nice to have an input on one pin act as an output enable for several other pins, i.e. when...
Getting "Failed to read PPK metadata" issue on measuring current of external device with external supply. I use nRF6707 PPK booth with PCA10028 or PCA10040 (doesn't work in...
Hi All.
Currently we are using buttonless-dfu service to upgrade firmware via ble on an nrf peripheral-device (via nrf-connect app on mobile central-device). Next, in order...
I am trying to implement the central side code for the usbd_ble_uart example. My current target is the nRF52840 Development Kit but the final target is the nRF52840-Dongle...
Hello!
I am developing a solution that has a gateway and about 10 devices.
The devices has some sensors and their are connected in gateway. Actually I catch the sensor...
Hi:
I am having a problem with the fstorage and ble_stack_init. When fstorage is used before the ble_stack_init it works fine. If used after ble_stack_init, the fstorage...
Hi,
We are developing a BLE peripheral that support DFU and accompanying Andriod & iOS apps.
When using the following tools, (buttonless) DFU concludes successfully...
