Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Is model Publish Retransmit (Mesh Spec 4.2.2.6 and 4.2.2.7) currently implemented in the Mesh SDK? I noticed that with Publish Retransmit Count set to 1, the Zephyr Mesh stack...
In nrf52832 datasheet, it uses" 64 MHz crystal oscillator, using external 32 MHz crystal "
then, can I use external 16 MHz crystal or external 4 MHz crystal to drive nrf52832...
I couldn't find nrf_drv_timer.c file. I want to create timer so I try to different SDK for my work. I am using SEGGER IDE for prepare software but i encountered lots of problems...
Dear nordic,
I try to build BLE application everything works fine expect the UART. The UART has transmission issue.
it has no problem in receiving. but when i tried...
Hi,
I am using nrfMesh2.2 SDK. I want to add models other than GenericOnOff and configurationclient to the interactive_pyaci. How do we proceed with this?
I found the utility to create the binary image of the production data for my Zigbee device but cannot find any documentation on how to incorporate the generated BIN file into...
Hi,
I have a custom board with nRF52832 and I'm using SDK 13.1 and softdevice s132 4.0.5. I have a GPRS module that I will use to receive the new firmware image and I will...
Dear Nordic,
I installed nrfConnect 2.6.1 and lauched "BluetoothLow Energy" application. Then i selected my board and it asked "Device must be programmed ..." and loaded...
Hi There,
I'm interested to customize the eddystone TLM parameters as per the image below, which is replace the Battery voltage with Button detection On/Off.
I did...
I was able to successfully make the BLE Peripheral Eddystone Beacon Application in "nRF5_SDK_12.3.0_d7731ad" in Windows 7 32-bit (pca10040), using GNU Tools ARM Embedded version...
Greetings,
I'm fairly new to developing with Nordic ICs using the SDK, I have previously developed for some nRF51x MCUs using some modules that had an Arduino library...
hello , everyone
platform : NRF52832, SDK13.0 , project:\examples\ble_peripheral\ble_app_template
I meet such a problem, config app_timer in APP_TIMER_MODE_REPEATED and...
Hi,
I cannot get the interrupt on Timer1 to work. I have checked that the counter is matching the compare register by not enabling the interrupt. When I enable the interrupt...
According to the official suggestion circuit, I’ve deleted some functions which are useless for me, (the schematic circuit diagram and PCB are showed in the end) then I use...
