Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Good afternoon,
I am trying to get cell-tower information from ZTE-M/NB-IOT cell-tower information, in particular RSSI.
In addition - a constant refresh-rate, ideally...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am trying to support old phones without BLE 4.2 data length extension.
I have read https://punchthrough.com/pt-blog-post/maximizing-ble-throughput-part-2-use-larger-att...
I am working on a project where I need to transfer the data from nRF52832 to ESP8266 through UART. I made the connections RX to TX and TX to RX.
I am using ble_app_uart_c...
Hello everyone,
I am having a problem with powering my nrf51822, I have 2 Li ion batteries to power my nrf51822 and a stepper motor, I put the batteries in series to have...
Hello,
Kindly asking for some guidance... We're working on a solution that requires us to distribute unique data sets (i.e., each nodes gets a different data block, approx...
I am using sdk15 with softdevice 6.0.0 for proximity profile. By keeping bootloader as stable can I change the location of softdevice?? I want to use bootloader at the 0th...
Hi!!
I changed the example of SDK14.0.0's ble_app_uart and I am doing low power consumption.
I used timer interruption and now I am driving with power consumption of 1...
Hi all, I am working on a mesh project. I've read Mesh Technology Overview written by Martin and I wonder what will happen if a node receive two or more messages at the same...
Hello,
I'm developing a BLE application using nRF52 based on SDK15.2 using Sofdevice S132 under Windows.
The nRF52 is used to send data in notification Format. In...
hi....
i am using nrf52832 and peripheral device , microcontroller should run continuously , nrf should be in turn off mode and it should turn on when the data need to send...
Hi all,
We are using nrf52832 board in our product. We used serial dfu method to upload the bootloader. Its done with help of nRFgoStudio application.
We want to know...
Is achieving a data length of 251 possible in SDK 14.0.0, SoftDevicve S132 5.0.0 ? I tried updating my GATT table to 6000 bytes and my NRF_SDH_BLE_GATT_MAX_MTU_SIZE to 251...
Hello all,
I would like to know if anyone is willing to share nRF drivers for ADS1298.
There seems to be a Github repo containing drivers for ADS1298 with arduino.
Has...
hi engineer: I use the software version: SDK15.2; the hardware IC is nRF52832; the protocol stack is s132_nrf52_6.1.0_softdevice; when I add "init.advdata.p_manuf_specific_data...
