Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
I'm developing an application for the nRF52832 using the nRF5 SDK version 15.0.0. We're using the s132 softdevice, the sample secure bootloader (modified to use our company...
Hi, I have been running into a problem where I am getting inconsistently failure to start advertising.
Calling:
err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST...
Hello, I'm trying to write code to a custom PCB with a nRF52832 using the nRF52 DK and the following wiring:
However, everytime I try to connect the JLink is says...
I'm fairly new to working this close to hardware and am playing around with a few things. I'm trying to bit bang i2c over a couple of gpio lines and everything seems to be...
1.Does nRF52840 and nRF9160 have conformal shielding in manufacture procedure？
2.Do i need reserve shield cover for these two module when I develop product？
Hello,
I'm having trouble adapting my code which works for reading the MAX30100 sensor using TWI input with the NRF51 DK kit.
I would like to adapt this code to be used...
Hello, I am at a loss because this question has come up several times in your forums and the solution is not working for me. Every time I run my program I am receiving a NRF_ERROR_NO_MEM...
I have a nrf9160dk and I setup the whole tool chain by following the Getting Started Assistant. I can't figure out how to connect to the board. Probably just a simple switch...
We are in the final stages of product development and are planning to enter the first batch of production by the end of January. We have a custom board tested, software written...
Installed nRF5_SDK_15.2.0_9412b96 to use with the nRF528240 DK. The SPI example suggests using a makefile. My computer does not have "make", nor gcc. Did I need to install...
Hi all,
I would like to know if there is a way to use the NRF52180 as a central scanning device. I searched for central examples in sdk 14.x.x and 15.x.x but they have central...
HI,
I am using sdk 12.2.2 and nrf52. I have write characteristics in my beacon but I can only send 20 bytes in one write cycle. How can I send more than 20 bytes?
Hello all,
Would it be possible to do a simple model that has a 3-condition switching state to control Forward/Backward/Stop conditions? I am looking to implement this...
