Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi, I'm working on a project where I'm trying to make an nRF51822 play a basic sound (such as a beep). Is there a recommended DAC that should be used with this particular...
hi, i am using nrf51822 version 2, SDK 6.1.0, softdevice version 7.3.0.
because the nrf 51822 is version 2, i have no choice but to use SDK 6.1.0 not 11.0.0(latest version...
hi,
i am using ble_uart example for send 3 byte (midi format) of data over uart.
i am receiving data which is appended with past data and sends as a chunk of data around...
Hello, i'm making small android application for my own test purposes. I want to understand full structure of advertisement packet which i receive with my phone. I can't find...
Hi.
I'm using nRF51822 with softdevice 8.
I started working with the uart example. and it works fine.
However, I can't get the BLE to reconnect automatically once the device...
Hello, i'm working with nrf8001 right now. I know that nrf8001 can work like Peripheral(slave) device. This is working ok. Im wondering if it is possible for nrf8001 to work...
Hello I'm trying to utilise the multiceiver mode with nRF24L01 and Arduino, the idea is that an nRF will be able to send a message and six other receivers will be able to...
When I use nRF UART of android phone A and B to scan the bluetooth device, the scan result is below:
first picture is the result of phone A, second is phone B:
first one...
Hi,
I want to use nrf51 development board as a bluetooth alarm clock using internal RTC . How can I generate timestamps to determine current date and time. Can the timer...
hi.
i want to parse the data before sending to BLE UART.
i am fetching data from RX/TX pin. and now i want to do some modification in data before sending it.
this block...
Hi, I want to send a constant carrier during production testing of a product.
First I call sd_softdevice_disable(); then I do the following:
//Restart radio
NRF_PPI...
Hello,
in our application I can see, that sometimes the nRF51822 completely resets, during a BLE transmission.
I am using S120 as peripheral. The peripheral is connected...
Hello,
I am trying to understand the basic working principle of the bootloader so i tried the DFU example in the SDK 9 it gets compiled and when i try to flash into the...
Hello,
I am using BL600A module and Nordic softdevice and SDK9.0. The system is having NUS service and TX and RX characteristic. Now I have a requirement for firmware upgrade...
