I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi. According to nRF54L Series features page ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/device_guides/nrf54l/features.html ), second-stage bootloader...
I've been using ICMSG's IPC to exchange HCI messages between the netcore and appcore, and using SPI to exchange HCI information between the host and appcore. This setup enables...
I'm working on implementing a Bluetooth Mesh network where each node periodically sends messages containing a single float32 value or an array of float32 values (e.g., every...
Hello,
I update ncs from v2.3.0 to v2.8.0 in matter windowcovering project.
my prj.conf file:
CONFIG_PM_DEVICE =y
CONFIG_PM_DEVICE_RUNTIME =y
CONFIG_USE_SEGGER_RTT...
Hi,
I'm developing a firmware based on Zigbee CLI sample. And I enabled DFU of app core and net core via serial with serial recovery mode.
Using SDK v2.4.2 and nRF5340...
Hi,
I am trying to integrate i2c code in peripheral_uart example from ncs 2.8.0.
I am following the steps as instructed in this exercise:
Exercise 1 - Nordic Developer...
I have nRF Connect for VS Code v2024.11.75 and am using SDK 2.6.1. In Lesson 3, Exercise 1 of the nRF Connect SDK Intermediate course in step 8 the instructions show to open...
I am a long time user of Doxygen and I am familiar with its format. I have been using Doxygen manually in my nRF9160 code and it is working fine. I am using DoxyWizard to...
Hi I am working on a project where I am trying to implement Bi-directional communication between 2 nrf modules connected to stm32f411ve dev boards. I am facing issue with...
nrf52840 with the official usb hid_generic routine transplant, the computer's 2.0 port hot swap probability is very small power-off restart, other ports are not tested out...
1. dts config file, I2C_SDA is configed GPIO P0.09/NFC1 , I2C_SCL is configed GPIO P0.10/NFC1, months ago, I'm using the old SDK, I also found that these pins configed as...
Hi Nordic team,
We need assistance in determining the appropriate GPS mode for our application: A-GPS or P-GPS? Though we believe A-GPS is more suitable for the use-case...
Hello,
My coleagues and I have been developing our application on the nRF5340 Audio DK for a while now and everything is working fine. Now we are at a stage where we want...
I am working on a custom development board with nRF5340 MCU. I have used two mics and integrated the LC3 codec library. I have assigned the following spaces in the prj.conf...
Hello,
I'm using a nRF5340 DK and ncs version 2.3.0.
What i try is, to use calls like
sdc_hci_cmd_vs_zephyr_read_chip_temp() that is available in header file sdc_hci_vs...
