Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi,
I am trying to use the UART on my nRF9160DK board.
In my program I have 2 uarts in use. uart0 is used for printk output and uart1 is used to receive data in async...
Hello! I'm working on an application with precise timing and I'm using timers and PPI.
In the callback pulse_end_cb() I seem to get garbage instead of the parameters, which...
Hey, so we have been building a prototype similar to a hearing aid with the nRF5340 Audio DK. I had a few queries regarding the DSP block of CS47L63 Hardware Codec which is...
Hi,
I'm implementing a BLE GATT peripheral that has no display but it does have a button.
I'd like to make some characteristics only available to devices that are BONDED...
Hi,
I am using CJSON_LIB from nrf-sdk modules, I even tested this cjson lib in such a simple way in helloworld app (I attached the sample project.), and after running for...
Hi!
We're looking into possibility to use nRF5340 and nRF7002 to provide BLE and WiFi access to an external MCU. The idea is to use one of NXP's MCUs as the main processor...
In the Power Profiler, when I select a larger area in the data logger, then it stops updating the selection time. It works great till 16:40m, but then stays at this value...
Hi,
We have developed our code against SDK 2.3.0 and I wanted to try to upgrade the SDK to 2.6.0. I had to remove CONFIG_OPENTHREAD_CHILD_SUPERVISION from my prj.conf, but...
HI
I basically define uart_init(); in Main.
And use DEBUG below to decide whether to use UART.
#ifndef DEBUG
NRF_UART0->TASKS_STOPRX= 1; NRF_UART0->ENABLE =...
In the transition from SDK v2.5.x to v2.6.x, Nordic removed support for boards that don't have the nonsecure (_ns) configuration in the Azure IOT hub sample. In other words...
Hi
I developing a nrf9160 project and try to use FOTA, I reference to example /samples/cellular/nrf_cloud_rest_fota.
finally firmware can successfully downloaded
...
I'm learning to use the Zephyr toolchain and in the interest of connecting the Zephyr-side coding to the i2c protocols I am familiar with, I have some questions.
I'm trying...
I have my software set up so that it does some computation within the Attribute write callback function like this.
b roadcastKeyHandler does somewhat of...
We designed a board based on the nRF52840, and are using nrf5 SDK 17.1.0 with S140 SoftDevice. The board has an RTC, LSM6DSO as IMU, an opamp front end for the analog inputs...
I am looking at the "mesh_shell" example project. I was able to build the sample for nrf5340 dk this way:
- create a new build configuration for "nrf5340dk_nrf5340_cpuapp...
