SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
One of our customers provided their own SIM card for our nRF9160 based product, and the system works but they have been having higher than expected power consumption.
We...
Dear support,
It looks like there are 2 compilation issues in NCS 2.1.2:
ncs/zephyr/arch/arm/core/aarch32/cortex_m/fault.c : fault_show doesn't compile when CONFIG_FAULT_DUMP...
Hello,
I have a strange problem and after having searched in this forum and tried to realize proposals which were given at other tickets here I need support for solving...
Good morning,
I have nRF52840 Dongle.
I am looking for a tool that will allow me to connect to a BLE device based on its name.
Need:
- find the device,
- connect...
What I'm working on:
I'm working on a small project using this nrf52840 module:
www.minew.com/.../
Access to source:
If it helps to understand my issue, all the design...
In the function "bt_scan_filter_status_get(bt_filter_status *status)" [file: subsys/bluetooth/scan.c #1302], the variable
"status->manufacturer_data.enabled" is not updated...
hi devzone
I've trouble starting nRF Connect for Desktop v3.12.0.
I'm using nrf52-dk / pca10040 board and nrf5_sdk_17.1.
when I run the program "nRF Connect for...
Hi,
I do have a question about PCB layers. I did read it is better to use a minimum of 2 layer PCB, but why is this? By example is a single layer also OK?
I'm trying to...
Hi Team,
We are using Nordic connect SDK nCS 1.9.1 & nrf52833
currently have not changed any clock frequency they're at default settings, we want to know what is the...
Hi, quick question.
Software: SDK 17.1.0 with segger embedded studio
Hardware: nrf52833-dk
Background: I read that it is possible to take iq samples of the payload....
Trying to using IEEE-802.15.4 on nRF52820 with SDK-17.1.0, Librarie 802_15_4/raw/802_15_4_lib_gcc.a.
nRF52820 n ot support FPU so set -mfloat-abi=soft in Makefile
Encounter...
I successfully completed all exercises from DevAcademy using nRF Connect SDK v2.0.0 and nRF Connect SDK v2.1.1.
However, when I tried to experiment with DevAcademy Lesson...
I have not done anything with the SDK for a while so I updated Segger Embedded Studio to the latest: 6.40 and the latest nRF SDK 17.1.0 and built my project and I only needed...
Hello together, I'm searching for a way to go I max low power mode possible an then wake a from one of three reasons:
Timer/Clock
NFC-Field
GPIO
I searched the...
I have an application setup to use RTT for console and logging whereas UART is disabled. If I enable the UART async API then RTT stops working.
Working:
CONFIG_ESB...
