Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi friend,
I am using SDK16.0 and softdevice is S140 7.0.1 version. But SPI can only send out 1 byte. It can't call back the function of spi_event_handler, so my code is...
Hello everyone,
I have successfully managed to perform a DFU with a DFU package consisting of an app and a softdevice. I wanted to test what happens when I manually cancel...
Hello all,
I was programming the nrf9160 SiP using esp32 over UART and wanted to know how do I connect ESP32 to the nrf9160 SiP and upload the code through ESP32 over to...
SLM returns ERROR after AT#XSOCKETOPT=1,51 NRF_SO_RAI_LAST https://github.com/nrfconnect/sdk-nrfxlib/blob/main/nrf_modem/include/nrf_socket.h#L218
SLM returns OK for AT#XSOCKETOPT...
Hello I am using I am NRF SDK version 1.8.0 and nrf-zephyr v2.7.0-ncs1 (If a soultion exists on newer a rev, willing to upgrade now, otherwise it will happen some time in...
When PIN=0 P0.00 is used it doesn't work (No error message or failing, i also tried several other ports), no toggling output. The code works with PIN=28 (P0.28=LED1), led...
It is properly pointed to in the emProject file, and the SES IDE is able to locate and open it in file explorer.
I upgraded the liboberon to 3.0.8:
When I previously...
I have a successful build over my i2c application but, I do not get any text output on the console. So, to check I tried to build a new hello world project and run it but...
I'm attempting to use the "powf()" function in a Zephyr thread.
When I try to run:
LOG_INF ( "powf: %f" , powf ( 2.0f , - 8.0f ));
the result is "inf". (Code compiles...
After intsalling nRF Connect SDK 10.18.0 on an Apple M1 running macOS Monterey 12.6, I can't use nrfjprog at all:
❯ nrfjprog --version [error] Error in dlsym: dlsym(0x204ef57e0...
I am installing the nRF Connect SDK (on an Ubuntu 20.04 virtual machine) as described here: Installing manually — nRF Connect SDK 2.1.99 documentation (nordicsemi.com) . ...
Hi, I get the following error when I try to install nRF Command Line Tools fails to install on Ubuntu 22.04.
~/programs$ sudo apt install ./nrf-command-line-tools_10.18...
I need to install the nRF command line tolls for Visual Studio Code to work. On the download page it however shows the ARM version of the 10.18.0 Linux x86 64 deb file.
...
