Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi,
We have an issue that is puzzling us.
The symtoms are the following.
If we flash v1 of our application (using Segger Link) to our target, it works correctly, no...
Hello,
I am experiencing a power issue after the first ADC sample is triggered. Sampling 2 ADC channels using PPI and TIMER as the triggering mechanism. Here is a capture...
nRF SDK 17.1.0 sd140 7.2.0
I'm working on adding OTA DFU to ble_app_uart. I had my own custom service that was working and then added on the DFU files like ble_dfu.c and...
Hi,
This question was asked before here a year ago, but I couldn't really find a definitive answer in the thread
Is there any reason why I would not be able, technically...
SDK V17.1, nRF52840 SOC, s140_nrf52_7.2.0_softdevice.hex
I am attempting to configure a spi device from a ble gap disconnect event handler. Before the disconnect event communication...
Hello,
I have tried to find examples where I can use nRF52820 chips for Thread applications and I can't. Program memory is too small for any application as far as I've searched...
Dear,
- nRF connect SDK 1.9.1
- nRF5340 DK
Here is my code and config. I can assign some pin as gpio such as 0.04. Maybe 0.03 or 0.13 have other function mux, but I...
I was trying to build my own devkit based on nrf9160 and I wanted to which hardware to use to upload code to the nrf9160 chipset.
I tried getting the chips used on nrf9160...
Hi,
I am having a trouble to flash Nordic Thingy 91 on My PC.
I have followed the instruction as bellow.
https://www.nordicsemi.com/Products/Development-software...
Hello, I have trouble developing BLE devices with Nordic NRF5280 and SDK 15.3.
I use pm_local_database_has_changed() on the product to notify the bound device of a BLE service...
Hello,
I am working on BLE MESH using nRF52840. I am trying to put nRF52840 into deep sleep mode. For this I am referring to lpn example in BLE Mesh which makes use of Friend...
Hi,
I came across example ble_sdk_app_alert_notification in the examples\ble_peripherals folder.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Dear Nordic support,
I'm trying to install Nordic 802.15.4 sniffer but I am unable to see the DK as a interface in Wireshark.
My setup is:
- Windows 10
- nRF-Sniffer...
I would like to build a device that periodically will list all adjacent Bluetooth devices.
This device should do a Bluetooth inquiry and get all discoverable devices information...
Hello, I am developing a BLE - LTE sensor gateway using the NRF9160DK.
I have written code for OTA updating the 9160 chip over LTE, but I am not sure how to update the NRF52840...
