after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello everyone!
Has anyone ever implemented ANCS (Apple Notification Center Service) in ZephyrOS?
We are using nRF51822 SoC with the goal to connect to the smartphone...
Hi Nordic Dev community ,
using: nrf52840-DK SDK 15.2 softdevice S140 6.1.0,
Am getting a SoftDevice assert id=1 PC=0x17660 code=0x62D
App error handler id=1 PC=0x17660...
Dear Nordic Crew, I have got 5 adafruit feathers based on NRF52832 and nRF52833-DK so far. I would like to implement indoor localization based on BLE mesh and RSSI. As far...
Hi,
I am trying to integrate the Google IoT Cloud example into my CoAP Server. The example is using Secure API to esablish COAPS. I have enabled
CONFIG_OPENTHREAD_COAP...
I downloaded a project in named prj9160 from Github. The prj9160 had three folders : Azure, firmwre, mscerts. I run successfuly the following command :
west build -p always...
Hi everyone,
I want to run nrf_drv_saadc_sample in a loop but I do not want to use PPI and TIMER peripherals because they increases the power consumption of my device. I...
Hi , am working on mesh example from v1.8.0\nrf\samples\bluetooth\mesh\light_switch. In this example they are using generic on/off server , light LC server and other server...
Hi.
For example, for the nRF52832 BLE chip, could it, in some manner, be only visible/communicate with a specific/particular smartphone app? How? using the MAC?
Regards...
Hello, I have a nrf5340dk communicating with nrf52840 dongle connected to a pc with UART baud rate of 2M. Connection parameters are:
7.5ms Conn interval
1ms Slave latency...
Background The adxl362 driver native to the zephyr kernel doesn't support FIFO operations, so I built my own out-of-tree driver that relies on a new accelerometer API instead...
I wish to add a firmware version to my project. Because we are hoping to use OTA for updating I have set the configuration paramater:
CONFIG_MCUBOOT_IMAGE_VERSION
in proj...
After working with arduino's and microprocessors like the ESP8266 and ESP32, I recently started toying around with a nRF52840 dev kit. After going through some tutorials,...
Hello,
In my project i am using nrf52840 with my custom board and to upload the code through NRF_CONNECT application with soft device its uploading properly but with segger...
Hi, I have a problem configuring the PPP Modem correctly and I'm not quite sure what i'm missing here.
I'm running the code on a custom board. We are using nRF52832 to talk...
Hello dear!
1- What is the relation(formulas) between current in uplink I uplink and the data packet size?
2- What is the relation between the iDRX PDCCH repetitions ...
