after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
at Bluetooth core specification v. 4.2, vol. 3, part G, chapter 4.9.3.
An Error Response shall be sent by the server in response to the Write
Request if insufficient...
I use the nrf examples direction_finding_connectionless_rx,firstly i have no attena array,the other as describled i do by steps.
I use two nrf5340 boards.with building,i...
Hi,
I am working on nRF5 Thread 4.1.0 and I am trying to do implement Thread secure DFU.
I am following infocenter.nordicsemi.com/index.jsp
i have run the command...
We are working on a project in which we have integrated multiple modules and examples like GPS, IMU Sensor, SD card, Bluetooth, etc. Now I have to manually shut down all the...
Hello DevZone:
I can see that they are working on a module with WIFI6, my questions are the following.
Will the module have its own evaluation board or will it be integrated...
Very quick question:
I've created a device which implements the Legacy DFU Service. I've also created an Android Application that I plan to develop to be able to conduct...
My application code running on nrf51822 calls sd_ble_gatts_value_set to update a control characteristic. After 16 times receiving NRF_ERROR_BUSY status from this function...
Hi everyone,
first time posting here for me, let me know if i'm doing it wrong.
I'm currently developing a "modem module" built around nrf9160 and working with AWS using...
Hi,
With the NRF Connect SDK version 1.9.1 it is not possible to setup a Thread Coaps connection.
The DTLS handshake fails after Client Hello with an Alert message ...
Hi,
The below is our requirement for NRF5340
1. we have a DFU application with bootloader as an hex file
2. we have another app say blinky as an hex file
3. merge...
Hi all
My first post. I tried to finish one of Nordic tutorials. I need to use app from nrf connect(v 3.10.0): Bluettoth low energy (I have installed v3.0.1). I have nrf51DK...
got the thingy:91 following the getting started video had the bootloader updated and uploaded the right hex file for lte, the provided sim appears to be outdated so tried...
Hello, I am using the Asset TrackerV2 application (SDK 1.7.1) with the modem firmware (mfw_nrf9160_1.3.1). Recently the following error <err> aws_iot: getaddrinfo, error ...
Hello,
I have been developing on a nRF52832 DK using nRF5 SDK v17.1.0, and am very close to a production ready state. The final program will use soft devices, app_timers...
I want to develop a USB composite device using USB CDC ACM + USB Audio. I am not familiar with USB device protocol, so I hope to have a reference example. My development board...
