Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi all,
I'm a beginning hobbyist with nRF52. I'm programming a BC805m using my nRF52-dk and nRF Connect SDK v1.9.0 (zephyr & Segger Embedded Studio).
The learning curve...
Hi, I am new to nrf.
I want to interface Sparkfun capacitive fingerprint sensor with nrf52832.
There is Arduino lib is present for this module.
But I am stuck on how...
1. When I start the SEGGER Embed open project: when 10_hello_world_clock_gettime, the following pop-up error pops up: Did not finish 'cmake',
2. When I close the window...
In nRF Connect SDK 1.7.1, how to send hex data over the connection by AT#UDPSEND?
I use AT#XUDPCLI to create UDP client and connect to server.
For the AT#UDPSEND, it seems...
Hi,
1. How do I resolve this error?
2. waring line 93->line 165
3. error : line 104,line114, line128,line 138,
Thank you for all your assistance. Kind regards, Peter...
Hi,
ncs v1.9.1
dk: PCA10090 0.9.0
example :serial_lte_modem
Does this example have the following capabilities?
1. The hex data received from the server in EDRX...
Using the UART example of the 52DK with the TX and RX pins set as 8 and 6 the example works. If I try to change the pins to different pins such as 22 and 23, it does not work...
Hi,nordic
I'm looking for L2CAP Connection Oriented Channels example in NCS,such as Object Transfer Service.
can you tell me some information？
Thanks.
TRANSLATE...
Hi everyone, i would like to put this topic here so that new developers can benefit from it i hope.
when you want to measure the current you need a PPK-2 or Oscilloscope...
Hi expert,
I use the example below:
D:\Nordic\nRF51 SDK\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart
I changed UART pin from default pin0.08 and pin...
My goal is to implement dynamic pairing and connection to a Bluetooth device based on SDK16.0.0 and s132_7.0.1, and add a buttonless DFU function. By sending instructions...
I am trying to integrate GitHub - NordicSemiconductor/IOS-DFU-Library: OTA DFU Library for Mac and iOS, compatible with nRF5x SoCs library in one of the SwiftUI mobile application...
I was starting from multi-NUs.I need to send form a Master a message to 4 Slave every 50mS.
I see that up to 100ms It work but that at 50mS the comunication doesen't work...
Hello,
I was given a project that was built using nRF Connect SDK 1.6.0. I tried installing nRF Connect SDK 1.9.1 but received a bunch of compiler errors when building the...
