after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Dear,
When I try to use <nRF Connect for Desktop>, it will show this message below:
I checked, this is because the first web which is based on America, can not be opened...
Hello, we are currently using the nRF51822 chip, and have roughly 1000 units of this particular device out in the field. After a few months of use, approximately 20 of these...
Hello,
I came across a very consistent bug that occurs on the nRF9160DK and a custom board with an nRF9160.
Basically, if you try to send the AT commands "AT+CFUN=1...
Hi,
I'm working with Nordic nRF52832 and trying to install Nordic Semiconductor nRF CPU Support Package from SES, from Tools--->Package Manager.
However, I wasn't able...
Hi
I want to use the NRF52840-DK board to evaluate some circuits that communicate with the nrf52840 chip. I want to design the board to act as a header for the hevelovpment...
Hi!
I want to be able to configure my nodes (assign AppKeys) from my own mobile application. I would like to know if it was posible to provision the nodes from the nordic...
Hello,
I am using NCS 1.7.0 for our latest product development based on nRF5340.
We have previously used Open source zephyr project for our development. We have an application...
Hello, devzone. I'm developing end device on nRF52840 using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0. I've connected my device to Home Assistant(HA) and have some configuration...
I need to use both AIN0 and AIN1 of nRF52832. AIN0 is measuring once per minute and AIN1 is measuring once per second. What would be the best approach for this? Thanks
Hi, I'm trying to reading the data pins of a camera and store it in variable. I'm able to read single pins using
How would I read 8 data pins simultaneously. This is my...
Hi nordic. I want to turn on and off the modem of the nrf9160 when I'm not using it. When I am using it, I am using your FTP library to sent sensor data to my server. Here...
Hi everyone,
I am working on interfacing the nRF52840DK with a 24-bit mems microphone INMP441 through the I2S peripheral. As multi-sources pointed out that the nRF52840...
I'm using macOS 12.3 and Python 3.9.10 from brew. When I "pip install nrfutil" I get nrfutil-5.2.0. Trying to run that results in "NameError: name 'xrange' is not defined...
After installing software, on Linux environment, and run power profiler, all seems to work fine, but after select PPK2, (D4f942375182 device) appears on top selected, but...
