Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Setup: Windows 10, nrfutil verison 6.1.3, python 3.10.2, nRF 5 SDK 17.0.2
I have a custom board running the stock DFU firmware from the nRF5 SDK. The only changes we made...
There are many questions on DevZone on modifications to NCS peripheral_uart/central_uart NUS example applications to support higher throughput.
We have been mostly successful...
I would like to use the nrf connect sdk to connect to a device and 'discover' the GATT services it supports, the characteristics in each service, and then read the descriptions...
Hi everyone!
I ported some project from NRFsdk 17.0.2 (all works fine) to Zephyr rtos and faced with issue - when set high speed uart (460800 - 921600) then some bytes ...
Hi All
A few times ago, I installed the nRF Connect for Desktop v.3.8.0 on my PC.
Getting started assistant, Programmer, Toolchain manager apps were installed and everything...
I want to know about following things:
1). NRF_SDH_BLE_GATT_MAX_MTU_SIZE
2). NRF_SDH_BLE_GAP_DATA_LENGTH
3). NRF_SDH_BLE_GAP_EVENT_LENGTH
4). Connection event length...
Hi There,
I facing one critical issue with softdevice, I cannot get it work in freertos environment.
Hardware: customized board based on PCA10056
SW: nRF5_SDK_15.2.0_9412b96...
HI
I am using the I2S on the nRF52840DK I have constructed an array and all works well except once I start it , it continues to run, I cant get it to play the sample just...
Hi,
In the product I developed, there is a UI flow about the mode of pairing and binding, which has a limitation that it can only be paired and bound when entering this...
My nRF52 only advertises NUS.
When a phone connects (Android or iPhone), I want to force bonding.
It seems to be related to security. I have tried a couple things, but...
Hello ,
I am using nrf52810 and i have my own code and once its compiled hex file is created so if in case if i missed my source code and i had only my hex file is it possible...
HI I am using nRF52DK as central and peripheral. UART example was used in nRF52DK as central, and blinky examples were put in the rest of nRF52DKs to test the connection....
Hi,
Disconnecting connection during DFU, then DFU never works again.
I reboot device many times.
Application works fine and soft device works fine, buf DFU still fails...
Dear Dev-Zone Team,
I just got my PPK2 and wanted to test it on the nrf52840
It seams to work fine, I can see the advertisement peaks, however the average power consumption...
I am using vscode with NCS 1.9. I am trying to add RTT logs to MCUBoot as the product I am developing won't have an exposed Serial port. I started with the hello_world example...
