after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I set up and testet the Low Power node example, described here:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_examples_lpn_README...
Hello People!
I need to transfer large amounts of information between our custom hardware based on the nRF52832 chip (S132+SDK17), and our custom mobile app running on a...
Hi,
in the .dts file，partitions is
Can it be changed to the following?
This modification does not compile .
What should be paid attention to when modifying,...
I am trying to implement bonding in central BLE uart_app example code but I don't know how to proceed as I'm a beginner . Do we need to make any changes at peripheral side...
Hello Nordic team!
I'm following this tutorial from Nordic to do DFU OTA: https://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kit/posts/getting...
I am following this post regarding reading the static MAC address for the nRF52840: https://devzone.nordicsemi.com/f/nordic-q-a/68376/trying-to-extract-the-static-mac-address...
Hi, we have a device that reads two sensors on separate i2c buses consecutively and transmits these using ble_nus_data_send().
The i2c sensors are read on an interrupt timer...
Hello all,
I am moving from the Arduino Uno to the nRF52 DK on Segger. A big difference
When looking at the examples, I cannot see the so-called setup() method, so, I...
Dear Forum,
I have the following issue (my System: Ubuntu 20.04):
I created the secure bootloader with Softdevice S140 (v.7.2.0) for 52833 chipset, I use a 52833 Development...
I have an application based on the peripheral uart sample, using NCS 1.8.0. I need to build in a version string that is queryable, so that anyone who connects to the device...
When i intially burn the code on dk, my dk should be in system off mode ie all functionality should be off. Then i want to press a button for 5 seconds with which the device...
Hi,
I am using the nrf52840-DK with the nRF Connect SDK version 1.8.
I have modified the central_multilink sample to connect to a BLE peripheral which requires a secure...
Hi,
We have a mature product based on the STM32 ARM processor family running the uCOS OS and our development toolchain is IAR. The workflow has worked well in the past when...
Dear all,
I ran LPCOMP example from SDK16 on nRF52 DK and it works just fine.
But I've occurred some problem modifying reference voltage. I init the lpcomp the same...
Hi ,
I have my own custom nrf52832 pcb. I have 2 chips on my pcb.
I program my device with Nrf52 Dk.
When I program MCU 1. The program is uploaded successfully and i...
