Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Dear DevZone Team
The nRF9160 datasheet stipulates output power as +23 dBm. I read this as conducted output power at ANT pin and not EIRP which to my knowledge implies the...
Hi Nordic，
My customer is doing the BQB certification, and they come up with a problem.
When they test the 2402MHz channel, they found that power of 2400MHz is greater...
Hi
I am using NRF52840 SDK17.1 with ble_app_uart project to be a server role. Some behavior as below:
1. Use phone's app could communicate it successfully. Write and notify...
Hi everyone,
I am using nRF52832 DK to transmit data to another development kit. During advertising, I measure the current with PPK II and see that the DK draws a static...
For he IO pins you have identifed for LF use, is this related to the correct operation of BT (as in these IO would induce noise and affect the BT operation) ?
Hi,
We developed a product based on the eddstone example, I have a question about the minimum Tx interval,
Minimum interval = number of configured slots * APP_CONFIG_ADV_FRAME_SPACING_MS_MIN...
Hi,
I need to record audio using ICS43434 and then process the recorded audio with nrf5340. Then I need to write the file to the flash memory. I need to know is it possible...
Hi,
I have noticed some strange issues with the modem part while developing. Sometimes the Modem is not connecting to network anymore. Our code has a loop that uses
lte_lc_offline...
Hello, All,
I want to use the GPS positioning function of the nRF9160, currently using the "nrf/samples/nrf9160/gnss" sample for testing, the type used is GNSS_SAMPLE_ASSISTANCE_NONE...
Hi.
Hope someone could help me on how to scan and parse the Manufacturer Specific Data that comes after the Company ID. I am using zephyr with nRF52840.
Thanks!
I am using nrfutil version 5.2.0 on a Mac Pro M1, running Mac OS Monterey 12.1. I get the following error when I try to generate a private key
------
Us-MacBook-Pro...
I just bought an actinius icarus board, and am trying to connect to it on linux (or windows),
The problem is that when I plug in the board in the usb, it will only appear...
Hi
1、Becuse of customer's PC administrator has been implanted managed software in the engineer's computer，So the m anaged software may limit some processes in the computer...
Hi,
After upgrade from nRF Connect SDK 1.4.1 to SDK 1.7.1 we have seen an increase of the current consumption with about 100uA.
Before with SDK 1.4.1 the idle current...
