Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
It's now two years ago, and the ticket had a different scope. But one of the answers from Nordic there was:
"This is because the spec mandates that if the device gets rejected...
I have installed the NRF Connect app on my Windows 10 PC, using "Run as Administrator" and keep getting the following error message whenever I try to install any of the products...
This is also my Bluetooth Prj.conf
When I turn on 2.4G, there will be an error message. How can I solve it? BLE and 2.4G cannot coexist at the same time. Can I switch...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
Hello Devzone,
How can the nRF5340 App core read the "version number" of the image flashed to the Network Core, e.g. the FW_INFO fields, or something similar?
I am using...
Hi,
Is there an API, data structure or else in nCS v2.9.0, monitoring of which i can understand if ble advertisement is active or not active or at fault.? Also, if at...
Hi, I am using sdk 2.3.0. I got the following warnings while building the project. The build finished without any error, but it didn't perform as expected. Should I concern...
I am building a project based on the aws_iot example. I am using sdk 2.3.0. I can connect with either lte-m or nb-iot, but I keep getting aws_iot_connect, error: -119. What...
Hello, I am working on a custom board with my own custom project. I want to perform DFU for all the images I mentioned. The mechanism for the OTA update will be as follows...
I am unable to read PDM microphone on my custom board or nrf54l15-dk.
My environment:
- nRF Connect SDK v3.0.2
- nrf54l15-dk
- custom board with Fanstel BM15C -...
Hello,
Revival of an old nrf52840dk board I would like to use for another project, I'm trying to flash a sample application to it but it always fails with the following...
The NDEF message is slightly different between Type 2 and Type 4. Type 4 has a 2 byte length field at the very beginning of the file, called NLEN. The NFC Type 4 example code...
Hi.
I made a board with nRF54L15. I would like to use P0.01 on nRF54L15 as GPIO output., but I failed to confirm P0.01 turn high.
Then, I asked nordic AI anything to solve...
I am trying to use sprintf to format a float type variable, and I am not having any luck. The values printed are either blank or wrong. Sometimes I even Hardfault, which I...
