Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi Support Team
Sorry, I accidentally pressed the wrong button and closed the following case. I still want to check the following two questions. Many thanks.
(+) Does...
Hi Nordic team,
We are using the nRF54L15 with nRF Connect SDK v3.0.2 for a BLE-based product.
We’ve observed something strange as below:
Advertising range is excellent...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
Background:
Over the past few weeks, I have been working on enabling TLS1.2 for an nRF9160 with Ethernet (W5500). My primary objective is to have both Ethernet and LTE...
Hello everyone,
Currently we're trying to get the full WiFi stack working on nrf7002dk. We decided to look into the power consumption of the DK board itself as a point of...
The Nordic Thingy:91X board has a Nordic nmp1300 pmic device, but the samples do not support the board (a lot of time would be saved it they did);
https://docs.nordicsemi...
Hi Support Team
Does nRF5340 support UAC(USB Audio Class) protocol? We want to input audio to nRF5340 via I2S and PDM and then output the audio to a PC via USB. Can the...
I would like to save about 100KB of data in the on-board FLASH of the nRF9151 SiP. Can you point me to the memory map and how I can partition the space?
I would like to create either a receiver thread that only monitors incoming/MT data OR setup a callback function to receive all incoming messages. Does such a thing exists...
I am using a custom nRF52832 board with NCS v3.1.0 with the following BT configs:
# Enable Bluetooth CONFIG_BT=y CONFIG_BT_PERIPHERAL=y CONFIG_BT_GATT_CLIENT=y CONFIG_BT_DEVICE_NAME_DYNAMIC...
Hello,
im trying to install the credentials into my nrf9160 , the error i get is this one : Failed to obtain CSR from device.
How can i solve this issue? I have also...
I do step-by-step elements from https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-5-fota-over-bluetooth...
I am trying to implemented a mechanism for authenticated debug on NRF52840 on NCS 2.5.
My understanding from the product specification is that DAP protection is enabled...
HI，
The current SDK version I'm using is 3.0.0 for nrf54L15. I want to control the SPIM30 using DPPI, so I'm using the nrfx library to operate the SPIM30. The specific code...
